01 January 1970 0 9K Report

Hey everyone.

I want to study the vortex dynamics in the superconductor MgB2 by the Monte Carlo method.Is it - possible? If so, can you suggest some avenues for research and the properties that we can study?

More Sliman Omar's questions See All
Why does flow deformation occur at the test line and control line on nitrocellulose membranes (LFIA)?

I use 1% BSA in 10 mM phosphate buffer (pH 7.4) solution when striping my nitrocellulose membranes with antigens and antibodies. However, I always observe deformed flow when my sample or running...

16 February 2021 4,224 3 View

How can I set up UV irradiation for crosslinking lab?

Hi, I am using a mix of 2 polymers and want to try and crosslink them. I have a UVA lamp of 365nm and have tried the lab previously at 30cm above. How would you recommend I approach the lab and...

31 January 2021 8,711 3 View

Which air pollution/air quality books do you recommend for working with environmental engineering students?

I am exploring up-to-date books on air pollution and air quality, and I would like to know which books do you recommend for environmental engineering students.

25 January 2021 3,972 7 View

How to simulate Sloshing water using Dynamic mesh in ANSYS Fluent ?

I am trying to model sloshing water in a tank in ANSYS Fluent using Wall motion. BUT it seems that System coupling is not responding to wall motion and it works only with Dynamic mesh.

20 January 2021 2,963 3 View

Are there other models that meet the same purpose?

Both Jakes and Gaussian models are used to characterize the power spectral densities of mobile communication channels.

11 January 2021 759 3 View

SDAS, secondary dendritic arms space relation with solidification rate?

Want to know the relation between sdas and solidification rate, the mechanism by which getting smaller space between secondary arms by increasing the rate ?

23 December 2020 735 2 View

Shall i use the country's CPI score or rank while entering the data ?

I have the Corruption perception index as a control variable in my study and i'm not sure what i have use the score or the rank of the country ? please advice what i have to use in the data entry...

09 December 2020 3,797 2 View

Any thoughts for a research topic in a master's level thesis regarding combination of Supply chain and entrepreneurship?

Hi, we are two master's students at JIBS and currently looking for inspiration and suggestions for a research topic that has a connection of both "supply chain" and "entrepreneurship". maybe...

18 November 2020 2,524 3 View

Can electrophoretic mobility measurements of polymer-coated AuNPs be used to infer the role of charge (if any) in their dispersion stability?

Hello Everyone, We have stable citrate-coated AuNPs dispersed in water. Different polymeric protective coatings (PEG, PVP, BSA) have been chemically grafted to the citrate-coated AuNPs for...

17 November 2020 2,903 16 View

How can instructors assess the intercultural competence of their ESL students?

Intercultural competence is a skill rarely taught and measured in ESL venues. What is an ideal way of measuring the student's progress in developing intercultrual awareness and testing it?

08 November 2020 2,176 16 View

Similar questions and discussions
MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein?

Hi In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein? I got this error in the add-ion stage: Fatal error "./ amber99sb-ildn-HHH.ff / force...

01 March 2021 8,747 4 View

How can you bring two structures together to create an adhesive bond in LAMMPS?

I have created an Ice 1h crystalline structure and an Aluminium substrate structure and equilibrated both at 250K. Now I need to bring them together in a way that an adhesive bond is created....

01 March 2021 3,325 2 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close