What are the most reliable approaches to extract key continuous frames from a video, with complete automation?

I have an input video, of skin (from a microscope that means it is magnified such that blood capillaries are visible). The idea is to extract 15 sec of continuous frames from a video of 1 min,...

02 March 2021 2,735 2 View

Which microtomy technique do you suggest for thin and delicate root sectioning ?And, how to preserve and process the roots before sectioning?

We have thin roots of from 1 year old different species of plants. We are looking into anatomical details of the roots. What's the best method to preserve and process the roots once they are...

23 February 2021 1,898 1 View

Has anyone done Archard Wear Simulation of GFRP Composite Plate in ANSYS with ACT extension or UDF?

I'm looking to do a sliding wear (plate-on-plate) simulation of GFRP composite plates with Archard Wear Model. Any hints or example steps are appreciated.

17 February 2021 1,447 2 View

Which root in this tap root system, in the picture attached, should be used for root sectioning in order to study the root anatomical details?

There are numerous roots in this tap root system. Kindly suggest or share a research paper where I can clarify the doubts as to which root should be chosen for sectioning and for further root...

14 February 2021 1,816 3 View

Possible problem for showing 0.2 sun intensity instead of 1 sun intensity in AAA class Newport solar simulator?

We have a AAA class Newport solar simulator. We changed the Xenon Arc Lamp recently (XBO450W, Make:OSRAM) as the lifetime got over. However, the intensity is coming to be only 0.2 sun instead of 1...

14 February 2021 9,998 3 View

How can I get access of UNAfold tool?

I am searching for tools to construct molecular beacons which shall be complementary to a given sequence. I don't want to design any primers. I found that UNAfold is one such tool which I could...

02 February 2021 9,065 5 View

The peptide synthesized with CTC resin have mass more (+68 Da) than the desired mass of the synthesized peptide. What could be the reason?

I am synthesizing 7 amino acid long peptide sequence with CTC resin, 50oC coupling for 10 min. On cleavage (TFA/TIPS/Water 95:2.5:2.5) I got peptide with good yield. However, It has 68 Da more...

30 January 2021 8,483 3 View

How do we calculate curvature value in ArcGIS?

Hello everyone, I am trying to prepare curvature map in ArcGIS 10.4, using spatial analyst tool. I am using 10 m CartoDem (projected in UTM 44N). I am getting very different value, curvature...

12 January 2021 504 4 View

How can a publish my case report?

I want to publish a case report regarding jejunal diverticula

02 January 2021 7,630 5 View

How can we maintain the two different DC high voltages of same polarity between parallel electrodes inside the vacuum separated by few millimeter?

I am trying to maintain two different high DC voltages of same polarity (either positive or negative) between two parallel electrodes separated by 500 um inside the vacuum. However, what I found...

21 December 2020 1,735 3 View

Does any one know how i can prepare liver tissue with transmission electron microscope with good fixation?

i have problem in preparation of liver tissue with bad cell organelles and how i can adjust osmolarity

03 March 2021 8,890 1 View

Do you know good and user-friendly programs to measure plant quantitative traits?

For my research i will need to measure plant quantitative traits (especially leaves area and roots length, but would be nice to add some more information). I recently discovered...

01 March 2021 5,035 2 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

Good morning research fellows, Has anyone worked with senna alata plant extract on any kind of fish?

Literatures on the piscicidal effect of sennaa alata is scanty. if you have any related litrature either in the bark, leaves or roots used as treatment to any aquatic organism please kindly help...

28 February 2021 9,138 2 View

How relevant is Mini slump cone?

for all the rheology researchers, my question is, how relevant is a mini slump cone (smaller than a standard 50 cent rheometer). currently based on testing, the thickness of slumped material is...

26 February 2021 3,668 1 View

Stress/strain tensors decomposition ???

25 February 2021 6,760 1 View

How to reduce residual stresses in MD simulation?

I am working on a preparation of representative polymeric structures of some popular polymers, such as polyimide or PTFE for MD simulation, during which a single nitrogen or oxygen atom will be...

24 February 2021 8,105 3 View

Suggestions for occupational stress surveys?

I am currently writing a masters thesis on reasons for occupational stress in the early childhood classroom, and want to include a short survey assessing participants work-related stress levels. I...

24 February 2021 8,678 2 View

Which microtomy technique do you suggest for thin and delicate root sectioning ?And, how to preserve and process the roots before sectioning?

We have thin roots of from 1 year old different species of plants. We are looking into anatomical details of the roots. What's the best method to preserve and process the roots once they are...

23 February 2021 1,898 1 View