The question about transverse shear stress for layered and stacked elements?

11 November 2018 0 2K Report

How to get the stress of 13 direction for the D point by simulation S8R elements? Besides, I don't know the reason that we cannot get stress of 13 direction of this D point by simulating stacked SC8R elements, and that layered and stacked solid elements have two values for this point.

The specific content is in the abaqus 6.14 document - Abaqus Benchmarks Guide - 4.9.1 Laminated strip under three-point bending.

Badges
Science topic

More Ray Guo's questions See All

How to add periodical boundary condition in FEM?

I have some questions about periodic boundary(PBC) condition that is used in FEM. 1. How to add PBC condition in the model? this is a abaqus model named PBC to add shear condition. The case for...

31 December 2018 10,100 8 View

When to choose general contact and contact pair as simulating contact by abaqus?

I think the major difference of general contact and contact pair is whether you need to automate contact definition as simulation. So I think we can choose either one except facing small slid...

10 November 2018 4,809 2 View

About abaqus contact problems

Recently, I am learning some abaqus contact knowledge. But now I face a pretty incredible problem. The analytical rigid bodies cause a pretty excessive penetration during the simulation. (The...

01 January 1970 7,894 4 View

New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before?

Question to you and THEM, the New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before? There appears to be a core problem for...

02 March 2021 3,024 2 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Does any one can help me choose a reasonable basis set for intermediate metal ions interactions with guanine (i.e Fe2+, Mn2+, Cu2+ and exc.)?

Hello every body Does any one has any idea to help me choose a reasonable basis set for intermediate metal ions (i.e Fe2+, Mn2+, Cu2+ and exc.) interactions with guanine or other DNA organic...

01 March 2021 6,187 2 View

How to assign different material properties to each element in Abaqus ?

Hello, I am writing a python script to generate my model and write the input file. The problem is I have 1000 elements in my mesh and I want to assign different material properties to each...

01 March 2021 9,511 3 View

How to define tie constraint between rigid body and another part in dynamic explicit model of Abaqus?

Hi dear researchers I connected a rigid body into the part of my structure by tie constraint and then I added displacement to rigid body, in static general step every thing is fine and these two...

28 February 2021 3,442 2 View

What could be some reasons why unstimulated monocytes are getting activated?

Im doing PBMC isolation -> CD14+ enrichment using magnetic beads -> stimulation setup. My negative control is just cells in cRPMI but they seem to get activated over and over again.

28 February 2021 7,883 3 View

Why does intensity drops as concentration increases?

Is there any reason for decrease in fluorescence emission intensity of HSA,BSA when increase the concentration ?

28 February 2021 3,653 4 View

How to modify Johnson cook equation in ABAQUS?

I wanted to add an extra parameter to the existing Johnson cook equation in the ABAQUS simulation. How to add those extra parameters. Ref: A modified Johnson-Cook material model with strain...

28 February 2021 4,841 3 View