Tensile test using ansys explicit dynamics for orthotropic material ?

More Abdul Rehman's questions See All

Post evaluation of close range photogrammetry experiments ?

I am performing a simple close range photogrammetry test and comparing outcomes of photogrammetry tools such as VisualSFM, Meshroom, Colmap etc. Kindly advice, what post evaluation tests/ criteria...

13 February 2021 6,410 3 View

In your experience what is the difference between G.652D and G.655D optical fiber. In field and in lab?

In our current era there is a big confusion about the usage of G.652 and G.655 optical fiber cable. Theoretically G.655 is much better than G.652 but the operator feel that G.652 is giving almost...

11 February 2021 4,006 8 View

Various schools have emerged in the study of comparative literature. Mention the most prominent of them in a nutshell.?

Various schools have emerged in the study of comparative literature. Mention the most prominent of them in a nutshell. And he talked about one of them?

09 February 2021 1,099 8 View

Data balancing before test/train split or only training data balancing. which is correct?

While reviewing technical articles, I encounter some papers where authors have used data balancing before splitting test and train (on full data), and some only balanced training data and let the...

04 February 2021 1,446 0 View

Mental health of COVID-19 Patients?

We want to conduct a study on the mental health and psychological problems in COVID-19 patients and would measure it in terms of Anxiety by Beck Anxiety Inventory, Depression by Patient Health...

02 February 2021 6,401 6 View

How can we measure disease severity of a pathogen in a crop?

severity index, measuring method and procedure detailed

01 February 2021 1,160 11 View

Why can't ANSYS Mechanical APDL detect the volume of my design ?

The 1st image shows the moment when I import my design(IGES) into the Mechanical APDL. The 2nd image occurs when I wanted to Operate>Boolean>Divide Volume By Area. The design is a regular...

28 January 2021 2,962 3 View

The lipid bilayer broken down and form micelle within 1ns MD simulation. How to simulate lipid bilayer without breaking bilayer?

To simulate the lipid bilayer (10-10, 25-25 so on) from CHARMM-GUI membrane builder, we used to simulate it at various force field (AMBER14, AMBER03, AMBER14IPQ, AMBER15FB, NOVA, YAMBER) at water...

26 January 2021 7,816 2 View

How to calculate radial distribution function (RDF) of a complex from Ab initio MD simulation trajectory?

Hi all, Is there any software or webserver to read the molecular dynamics (MD) simulation trajectory which obtained from Ab initio MD simulation to calculate the atom-atom radial distribution...

25 January 2021 9,474 3 View

Is PV array not available in MATLAb 2020a simulink?

I have MATLAB 2020a. PV array is not present in the simulink library. Can anyone please explain if the name of module has been changed or is it not available anymore? Is there any way to add PV...

24 January 2021 7,962 5 View

How to compare two groups with only two measurements?

Hiiiii everyone! I have an enquiry on statistical analysis. I was looking for many forum and it's still cannot solve my problem. I want to compare means of two groups of data but only with two...

03 March 2021 8,796 3 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What SPSS analysis should I run with one IV (with two levels) and two DVs?

Hi, I am trying to figure out which test would be most appropriate to run for the following question: Is there a difference in task blood pressure between smokers and non-smokers? There are two...

01 March 2021 8,235 2 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

Subham Mukherjee

1. You have to decrease the load increment size to simulate the process quasi-statically. So, at first, reduce the load increment size.

2. Then check that the kinetic energy evolution must be less than 1/10 to 1/20 of the strain energy. Otherwise, dynamics in the system exist.

3. If the problem persists, check the boundary condition and try it with elastic material.