Dear all,
Please can you tell me what is the loading rate to test the concrete cylinders (150 mm x 300 mm) to estimate the tensile strength?
Best Wishes,
Najia
Approximately 0.02 - 0.1 MPa. You can follow this link, it is useful:
http://theconstructor.org/concrete/splitting-tensile-strength-test-on-concrete-cylenders/2116/
Thank you alot
Apply the load continuously without shock at a rate of approximately 14-21kg/cm2/minute
Dear all, I am using nntool to train my data, I have 3 input parameters and one output, When I entered the number of input data (3 x 120), and target (1 x 120) and training process finished. when...
08 September 2016 2,870 2 View
Dear all, I am looking for Design and construction of building structures with fibre-reinforced polymers CSA-S806-02 and Canadian Highway BridgeDesign Code CSA-S6-06. Please if any one have it,...
05 June 2016 3,963 0 View
Dear All, I am looking for the below MS thesis, I didn't find it in British library (ETHOS) Canadian library website for searching theses. it should be available in American library website....
03 April 2016 3,711 2 View
Dear All, I want to know how to estimate the compressive strength of concrete after 28 ages? is there any equation to calculate f'c after 28 days? I know compressive strength of concrete after 28...
02 March 2016 5,826 7 View
Dear ALL, How can I get the link for Rilem Data Bank? Some journal papers mention that they collect data from Rilem Data Bank. For example, I want to collect the experimental data of bond strength...
02 March 2016 8,204 1 View
Dear All, I use cohesive behaviour and damage to simulate the interaction between reinforcing bar and concrete, the definition of damage consists of two parts: 1) damage initiation 2) damage...
31 December 2015 8,192 4 View
Hello, I need your help for calculating correction factor. Please can you read the the below answer I found it in internet, but when I go to ASTM C42, I find the correction factors, but I don't...
11 December 2015 4,250 6 View
Hello ALL, I modelled the concrete reinforced with FRP reinforcing bars and I want to use nonlinear springs to connect concrete to bar. I read PhD thesis and he used JointC as nonlinear spring. I...
10 November 2015 4,550 5 View
I am looking for glass fibre polymer bar and basalt fibre polymer bar manufacturers in Europe. Manufacturer must have good experience in manufacturing FRP bars. Regards
07 August 2015 1,052 5 View
I modelled the pull out specimen in ABAQUS, I don't know how to define the bond behaviour between concrete and FRP bar? when I was using the tangential behaviour between them and I tried to put...
11 December 2014 312 2 View
How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...
10 August 2024 942 3 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
Details of the Analysis. Static Analysis Composite Layup Continuum Shell Elements FRP Material (Elastic and Hashin Damage)
03 August 2024 8,538 4 View
How do you tie-break and rank these two in their strength?
03 August 2024 4,471 1 View
Machine learning (ML) has shown great potential in predicting the compressive strength of concrete, an important property for structural engineering. However, its practical application comes with...
03 August 2024 2,546 2 View
N=6 Comparing pre and post test likert scale responses. Participants are mix of practicing & preservice teachers.
30 July 2024 7,233 4 View
Accredited laboratory of JV "Uz-Kor Gas Chemical" LLC (Uzbekistan) is looking for providers to conduct interlaboratory comparison tests on gas chromatographic analysis of hydrocarbons (component...
25 July 2024 8,108 0 View
Dear all, I gave 116 respondents 18 translated sentences and asked them to indicate their levels of acceptance of these translations on a five-point scale. Some translations result from strategies...
24 July 2024 8,245 5 View
I am working on scale development in behavioral finance by undertaking a mixed-method approach using the exploratory sequential design. The phenomenon has diverse meanings in existing literature...
20 July 2024 9,153 11 View
Hello everyone, I am currently working on a project where I aim to analyze color preferences in data visualizations across participants from three different countries. The dependent variable in...
19 July 2024 4,178 2 View