Is it possible to set a breakpoint at a specific DYNAMIC instruction using the GNU Debugger (GDB)?

Using GDB, it is straightforward to debug and monitor a target program by setting a break-point at a specific instruction, since the instruction addresses are known. However, we have two...

24 February 2021 1,598 2 View

Whic Type of Thermal Camera is Good to use in animal research?

Hello dear researchers I want to use a thermal imaging camera to livestock study. I wonder which type to use. If you know or used a good type please comment or insert its online link in...

29 January 2021 4,163 4 View

What are the most practical applications of nano fluid in air conditioning systems ?

explain your idea

01 January 2021 8,593 2 View

Which is the best software in Organic and Perovskite solar cells simulation SILVACO or Fluxim (SETFOS)?

I need to use a new software in Organic and Perovskite solar cell simulation

24 December 2020 2,397 4 View

Please , can the concentration of the drug inside the nanocarriers or nanoparticles be determined using a UV spectrophotometer ?

Please, can the concentration of the drug inside the nanocarriers or nanoparticles be determined using a UV spectrophotometer after getting the calibration curve of the drug alone?

19 December 2020 4,634 5 View

How to correct time series data if there are missing values from the original source?

Some times there are missing values for some years in time series data, how to deal with this problem?

11 December 2020 1,263 3 View

Does the Chinese navigation satellite system (Beidou) become global or still regional?

I know that this system was regional before, thus covering specific areas not alla the global

09 December 2020 3,343 3 View

Do you have the XRD JCDPS of Polycrystalline ZnS?

Hi, I need the JCDPS of polycrystalline ZnS, it would be appreciated if you could help me through this thank you in advance

30 November 2020 3,342 3 View

What are the best kind of mesh to save the running time in 3D trapezoidal cavity ?

explain your idea

24 November 2020 9,036 2 View

Does the freeze-dried change the color of the NCQDs quantum dot?

I have synthesized NCQDs using citric acid and urea as precursors. The powder-color of the quantum dot after the freeze-dried is green; however, the color will change to black as stored at room...

29 October 2020 3,700 3 View

How can I verify my centrifugal fan design for electric motor cooling?

I have radial blade centrifugal fan design which will be mounted on exhaust side of electric traction motor. The fan will be mounted on same motor shaft inside the housing. How can I verify that...

23 February 2021 2,390 3 View

How do I calculate the torque required for linear motion?

23 December 2020 5,064 3 View

How can I make my actuator transfer linear motion into vacuum?

I have a linear actuator of 1kN load capacity, 50mm linear travel, and M35X1mm thread at outer body. The spindle has M10 internal threads which is not through (closed end). I am having leakage...

25 October 2020 3,990 2 View

How to calculate rotation of brushless DC Motor using duty cycle?

Hi everyone, I am trying to model brushless DC Motor in Simulink. At one point, I am in need of the motor rotation and the only parameter available to me is the duty cycle and the direction of...

11 March 2020 1,240 3 View

How can we simultaneously connect the internal combustion engine and the electric motor to the propeller without loss?

How can we simultaneously connect the internal combustion engine and the electric motor to the propeller without loss?

17 January 2020 288 2 View

How Can I integrate DC Motor Dynamics into LQR Controller?

Hello dear academicians, I control my system with a LQR . My input (u) is torque produced by 3 reaction wheels. These wheels are connected to DC Motors. Reaction wheels inertias are already...

05 January 2020 2,702 12 View

Who has electric motor efficiency data?

Hi, I'm working on a polynomial motor efficiency model for control allocation. This model is based on experimental data to tune the coefficients. I'll be glad if you have efficiency VS Torque and...

09 October 2019 2,268 3 View

Capacitor start induction motor "optimization" in ansys maxwell. RM Xprt ?

I have simulated the 0.37KW capacitor start induction motor in ansys maxwell RM Xprt. Its efficiency is 45% (percent), results attached. These are no load results. I have few questions How to...

09 October 2019 5,156 2 View

How to increase stiffness of the part?

I am doing strength analysis of the electric motor in abaqus. It is in three steps. in the first step the boundary conditions will be applied, in second step contact over closure between motor...

10 September 2019 4,101 3 View

How to increase stiffness of the part?

I am doing strength analysis of the electric motor in abaqus. It is in three steps. in the first step the boundary conditions will be applied, in second step contact over closure between motor...

08 September 2019 6,173 3 View