I need an appropriate state space model of Active power filter which I can implement on Simulink, I found many of them but not well emphasizing .. so if there is a Discrete state space model which I can implement and understand, I will be grateful.
Dear Akram
Please see the attachment sites
Regards
https://ieeexplore.ieee.org/abstract/document/5559218/
https://ieeexplore.ieee.org/abstract/document/1339343/
https://ieeexplore.ieee.org/abstract/document/1355106/
https://ieeexplore.ieee.org/abstract/document/6078690/
Hello!
Akram Elhelbawy
I am sending some useful links to you, I hope these links are helpful for you to compete your research
1. https://in.mathworks.com/matlabcentral/fileexchange/61215-three-phase-shunt-active-power-filter-using-pq-theory
2. https://www.semanticscholar.org/paper/Simulation-a-shunt-active-power-filter-using-Lada-Bugis/55c3a39d1d6cb7138fa1cf2667a48c83597e669b
3. https://www.semanticscholar.org/paper/Matlab-Simulation-of-Single-Phase-Shunt-Active-on-Singh-Bhavsar/0bfbcdcb0271f844768fbbb939cb47c235b6839e
4. https://in.mathworks.com/matlabcentral/fileexchange/42627-shunt-active-power-filter
5.https://pdfs.semanticscholar.org/0bfb/cdcb0271f844768fbbb939cb47c235b6839e.pdf
why it is better to implement the same algorithm but without loops? Example: If I have an array of values, I want to substitute them in a specific equation. I can do that by 2 ways: 1) loop for...
08 September 2019 8,768 1 View
simply, I can put a PI block in simulink and specify gain and sampling time .. BUT this time I need to remove this block from simulink and put a function block, where inside, I can set Kp .. Ki.....
07 August 2019 7,470 5 View
Well .. my question is too simple. I need to know how to model rectifier circuit in state space model [A B C D] rectifier circuit simply consists of: voltage source, MAYBE line inductane,...
07 August 2019 3,493 6 View
I have inverter and I need to use MPC to select an appropriate input "u" to be applied at specific time from a series of input u. how I can do it in code of MPC ? for example, u = 000 010...
06 July 2019 1,508 3 View
I want to apply Wavelet on noisy signal NOT image on matlab, but it always asks me to have 2D data ... My objective: I want to extend a specific frequencies from these noisy signal any ideas or...
06 July 2019 3,929 8 View
my whole simulation which contains the inverter on Simulink is discrete time system with discrete block 2e-6 sec I made a state space model for the inverter system Xdot=Ax+Bu but I guess that I...
05 June 2019 6,176 5 View
For Hikers/riders, they carry a GPS device which is connected to satellite and they can send messages to their family and friends .. If I want to build a system to host all kinds of these devices...
04 May 2019 3,077 5 View
Well .. I work with harmonic elimination in general .. I formed a system of 3 phase voltage source connected with bridge rectifier and load ... and of course as a result there are harmonics in...
03 April 2019 6,177 6 View
Is there a straightforward way to conduct a sensitivity power analysis for a Kendall's Tau correlation? I was considering using the sensitivity setting and "Correlation: point biserial model" test...
28 July 2024 6,133 8 View
There are many types of symbolic judgements. For example, when an Israeli pilot flattens the home of a Palestinian family (even if they are forewarned), it is natural for them to experience shock...
28 July 2024 2,610 1 View
PDE value for Tert-Butylamine
24 July 2024 1,166 0 View
Hello, I have a somewhat weird question: has anyone had problems with campylobacter growing in the second half of the strip GLU through ERO? Have you managed to correct it? There is some...
19 July 2024 3,094 2 View
I am conducting a study aimed at exploring the correlation between introversion and social phobia among Lebanese adults. I need to calculate the minimal sample size using G Power, but I'm not sure...
19 July 2024 6,048 1 View
I have a Simulink model that connected a main utility (AC-grid) with a three-phase load changing from 20kW to 100kW in 5 seconds and I don't know how to build this load in Simulink. Please your...
14 July 2024 8,892 3 View
I am using a polygon mirror scanner that have 6 facets and the dc brushless motor speed was given 10,000 RPM. Now I want to know how to calculate the polygon speed if I change the power supply...
11 July 2024 5,942 1 View
How is biomass energy essential in the power generation in a country.
08 July 2024 9,477 2 View
I want to calculate the sensitivity using G*Power. If I have understood correctly G*Power gives me the detectable effect size for three-way interactions if I enter the number of groups (meaning...
08 July 2024 8,653 2 View
I am trying to do a matlab project on power system state estimation. I am doing using WLS,EKF and particle filter method and then comparing these all. To minimize the error can we use Machine...
04 July 2024 6,845 0 View