Standard and guidelines on galvanized?

Majid Oghabneshin @Majid_Oghabneshin

11 November 2015 0 6K Report

how can i find standard and guidelines on galvanized coating process?

Badges
Science topic

More Majid Oghabneshin's questions See All

Coating and related standards?

hello. which coatings and standards are used on hulls of ships.

06 July 2016 3,077 3 View

What relationship is used to calculate the galvanic corrosion current density?

if we have the potential difference in a galvanic couple how can we calculate the corrosion current density?(what is the corresponding relation?)

01 February 2016 5,000 2 View

How can we illustrate the improvement in corrosion resistance of Al 5083 alloy with anodic Al3Mg2 precipitation after 5 cycle of ARB process?

I have applied the ARB process on Al 5083 aluminium alloy. This resulted in the grains to become ultra fine. and consequently the corrosion resistance has increased in comparison with the as...

09 October 2015 8,510 5 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

How do I conformally do PR spin coating on trench structure?

I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...

08 August 2024 2,298 0 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

Can we patent a process flow diagram developed using a process simulator but no actual cases is carried out?

Can we patent a process flow diagram developed using a process simulator but no actual cases is carried out? For example consider a process for certain product manufacture where a new process flow...

31 July 2024 781 1 View

What is the reason I get 400nm nanoparticles using an extruder with 200 nm membrane for cell membrane coating?

I am trying to coat my micelles and PLGA based nanoparticles with cell membrane using an Avanti mini extruder according to literature . I use 200nm membrane but my particles end up to be 400nm And...

30 July 2024 3,294 3 View

What is the main used curing agent for epoxy based coating?

I am trying to coating metal oxide into steel substrate, for better sticking planning to utilse epoxy based, Could you please suggest suitable curing agent for the coating purpose

25 July 2024 438 3 View

How do you get pure primary macrophage cell culture?

I have been harvesting monocyte-derived macrophages from buffalo and cattle fresh whole blood using the same protocol for years and getting good macrophage cultures. Below is the protocol that I...

23 July 2024 4,074 2 View

How to Select the most suitable machine learning algorithm depending on the characteristics of the given dataset ?

I'm working on a project that involves analyzing a new dataset, and I'm at the stage of selecting the most appropriate machine learning algorithm. The dataset consists of both numerical and...

22 July 2024 6,097 7 View

Is it appropriate to apply the COSMIN guidelines for evaluating the quality of tools used to assess acute postoperative pain?

Hi, I'm a graduate student, college of nursing, chungnam national university in Daejeon. The topic of my thesis is "Quality Assessment of Tools for Evaluating Acute Postoperative Pain." I have...

10 July 2024 3,048 1 View

Issues in coating of cathode material on Al foil, why we are not getting proper coating and results when the cathode was coated on Al-foil..?

We are trying to coat some cathode materials on Al-foil ( ex - LiFePO4 , S@CNT, etc). When we coated the Al foil with the cathode (ex - S@CNT) material , the cycling result was annoying. But the...

09 July 2024 5,123 4 View