What thickness need for ITO to use as conductive layer?

I want to do RF sputtering of ITO on glass substrate using magnetron sputtering. what thickness do i need to make it good conductive layer to use it for PSC. Moreover, whats about thickness of...

01 March 2021 395 3 View

Are protein samples in SDS compatible with ELISA?

I have used an AllPrep DNA/RNA/Protein Mini Kit QIAGEN kit to extract RNA and protein from my samples. At the end of the protein purification, I resuspend my protein in 5% SDS. Will these samples...

28 February 2021 7,370 3 View

Special issue on PLS-SEM in Mathematics. Are you interested?

21 February 2021 5,601 3 View

How to calculate the TCID50 when the highest CPE is 50% or less?

I am doing TCID50 to measure progeny virus and some treatments protected the cells in a way that the highest CPE observed is 50% or less. How should I do the titre calculation in that case? Thank you!

16 February 2021 8,768 1 View

Which drug is better to modify blood pressure in awake monkey, if I provide it in the food or drink reward?

I need to modify the blood pressure in a monkey while is awake in the recording chamber, and I am planing on provide a drug for that in the food or water used for reward... any advise? Thank you

08 February 2021 9,900 1 View

Why stop the reaction in ice for the fluorescent probe FDA (fluorescein diacetate)?

Hi, In literature I noticed that who stains haemocytes with FDA for 30 min then stop the reaction in ice while this does not apply for 15 min incubation time (or maybe authors did not write this...

08 February 2021 3,366 3 View

How to make Fast Green FCF from powder?

Hi everyone We need Fast Green to electroporate plasmid into mice embryos, therefore we simply need it to see some color in the liquid we are electroporating so that electroporation is more...

07 February 2021 1,671 2 View

Why do high doses of humic substances inhibit the growth of corn roots? Is there a toxicity effect?

Length, volume, surface area and dry mass of corn roots treated with humic substances increased up to 13 liters per hectare and decreased with higher doses.

02 February 2021 2,190 4 View

Using a nucleosil c18 column, i get no negative peaks in real time and two negative peaks in post run.Software problem?

Simadzu, lc solutions

02 February 2021 1,969 2 View

Any ideas on fast and easy way to stain mucus on intact cell layer?

Dear RG community, We are looking for a fast and easy way to stain mucus on a cell layer that allows for macroscopic visualization of mucus distrubution. Our epithelium is grown in conventional...

31 January 2021 6,790 2 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How relevant is Mini slump cone?

for all the rheology researchers, my question is, how relevant is a mini slump cone (smaller than a standard 50 cent rheometer). currently based on testing, the thickness of slumped material is...

26 February 2021 3,668 1 View

Stress/strain tensors decomposition ???

25 February 2021 6,760 1 View

How to reduce residual stresses in MD simulation?

I am working on a preparation of representative polymeric structures of some popular polymers, such as polyimide or PTFE for MD simulation, during which a single nitrogen or oxygen atom will be...

24 February 2021 8,105 3 View

Suggestions for occupational stress surveys?

I am currently writing a masters thesis on reasons for occupational stress in the early childhood classroom, and want to include a short survey assessing participants work-related stress levels. I...

24 February 2021 8,678 2 View

The most suitable method to calculate the stress intensity factor in the presence of contact between the crack lips?

I'm trying to study cracked structures under a compressive load taking into account contact between the crack lips. I would like to know if the method of extrapolation by displacement remains...

21 February 2021 8,694 4 View

How to assign two different material/section properties in Abaqus(UMAT)?

Hi everyone, I am conducting a non-linear multi-layer pavement structure analysis which is a stress-dependent. So far, I am able to define the nonlinearity for one soil layer for its resilient...

11 February 2021 9,607 3 View

Are there any exception like work hardening in metals elastic limit due to dynamic loading?

The samples made out of spring steel are taken from same lot. The specimens were shaped following heating to forging temperature - Forming- Hardening -Tempering methods. After storage of almost 6...

11 February 2021 952 6 View

How to write cyclic loading in OpenSees?

Hi there, I'm having trouble with adding cyclic loading in OpenSees software. My task is to model a reinforcing bar under cyclic loading and compare the response with the experimental results....

04 February 2021 8,158 1 View