Sintering dissolution process(aluminum foam)?

Rohollah Fallah Madvari @Rohollah-Fallah-Madvari

27 September 2019 0 9K Report

I am going to make open cell aluminum foam with sintering dissolution process (solid state and COLD PRESS) method.

Please help me how I can remove aluminum powder film oxide?

Badges
Science topic

Similar topics
Social Psychology
Attitude

More Rohollah Fallah Madvari's questions See All

How can I use proc nlmixed for two-level joint model for data that is not longitudinal?

11 May 2024 4,239 0 View

How to measure bond disscoaition energy of ReaxFF with lammps?

Hello, I have a script changing the distances of two bonded atoms and I calculated the total energy (or potenial energy, kinetic energy is zero) with energy minimisation tool of lammps (ReaxFF...

27 March 2024 4,468 2 View

Difference between output power variations of (Pd - coated) and (Pd-Cu -coated) tapered optical fiber?

Output power changes on the optical fiber sensor for hydrogen gas have been illustrated. Why does the Pd-Cu sensor show no sensitivity at low hydrogen percentages while the Pd sensor does? Why...

01 January 2024 2,200 2 View

Change in multiple band gap of CuSe after Ni-doping?

The band gap results for CuSe and Ni-doped CuSe, according to the Tauc plot and the mathematical DITM (Derivation Ineffective Thickness Method) model, in which thickness and type of transition...

29 December 2023 614 2 View

Conceptually, why is the energy of a hole considered greater than that of an electron?

We know that electron mobility is higher than hole mobility because the effective mass of an electron is less than that of a hole. However, if we ask why the effective mass of an electron...

14 December 2023 3,546 11 View

EDX result of sputtered tapered optical fiber with palladium and copper.?

Why are other elements such as calcium, oxygen, sodium, magnesium, aluminum, silicon and molybdenum visible in the EDX spectrum of tapered optical fiber (SMF‐28) covered with palladium and copper...

01 December 2023 7,414 4 View

Lower crystal quality together with lower band gap after annealing?

Why is it that after annealing, while the size of the particles has become smaller and the crystallinity has decreased with XRD, and the electrical conductivity has decreased, but the band gap has...

21 October 2023 5,950 4 View

A defect or something else in the AFM image for ZnO thin film prepared by sputtering?

What could be the reason for this situation in the AFM image? Is what is marked a DEFECT? and why. This is an image (AFM) for ZnO prepared by Sputtering method with -200 V as bias voltage and...

20 October 2023 7,855 4 View

How can get rid of bubble formation during the butyl adhesive injection via Graco Supply Systems which are suitable for pumping viscous compounds?

We are producing the PE based insulator of door panels for automotive industries. In order to waterproof the doors, the butyl adhesive must be extruded around the insulating foams. While butyl...

04 July 2023 6,703 0 View

Global Pressure and Temperature model (by latitude, longitude, Height and time)???

Hello erveryone. I want to try different global and temperature models and their data that want time, longitude, latitude, and height as inputs. I already tried different models for zenith...

04 May 2023 4,429 2 View

How are iso-frequency contours plotted?

Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...

07 August 2024 1,937 1 View

How to correctly use the UTE and ZTE pulse sequences in Bruker's ParaVision software?

I am using a Bruker 600M solid-state NMR spectrometer with a Micro 2.5 microimaging system. The test sample is a tube of 1M LiCl aqueous solution, and the nucleus detected is 1H. I am trying to...

01 August 2024 9,227 1 View

What is the solubility of Iron (+3) in Bismuth Oxide?

Dear all: I am modifying Bismuth Tungstate with Hematite (Fe2O3), so I would like to know about how much Iron(+3) can form a solid solution in a Bismuth Oxide matrix. Best wishes Marco

29 July 2024 2,163 1 View

Optimal siRNA Volume for Complexation with Liposomes in a 2.5 mL Solution with 10 mg/mL Lipid Concentration?

How much volume of siRNA can I add to 2.5 mL of liposomes with a total lipid concentration of 10 mg/mL?

27 July 2024 6,920 1 View

Non -oxidizing metal binders?

I'm trying to sinter some Nb parts and I'm trying to find a binder which does not produce oxidative compounds when it decomposes.

25 July 2024 9,823 3 View

Turning the Brain into a Vegetable: What does it tell Us?

A vegetative state is caused by having massive damage to the mesencephalon, which can include both the pontine nuclei and the thalamus (Plum and Posner 1980). During this state, the metabolic...

23 July 2024 6,177 0 View

What could be the possible reason that sintering of polycrystalline diamond fabricated with tape casting has suddenly started failing?

I make polycrystalline diamond with tape casting followed by HPHT sintering. When i sintered the samples up till May, the sintering was good. When i sintered the samples in June and July at the...

16 July 2024 3,212 5 View

How to calculate percentage cumulative drug release?

How to calculate percentage cumulative drug release when, Total volume of dissolution media = 250ml Added formulation was equivalent to 10mg of drug Sample withdrawn = 1ml each time Sink condition...

15 July 2024 4,192 1 View

How to prepare alcohol foam with high alcohol content?

Hi everybody, I wonder is there a way to prepare foam from iso-propanol/water mixture? The content of this alcohol should be 70 – 80 w.%. I plan to use silicone-based surfactants, I have several...

15 July 2024 3,539 0 View

How to change the author?

Hello! Research of factors affecting thickness of the covering obtained by electro contact sintering of composite materials. This is my article, not Varvara. How to change the author? Incorrect...

09 July 2024 3,829 0 View