We need suitable refrences for Set-up and electrochemical test standards for measuring the semiconductor gap band, could you please guide us?
It depends, which BG do you want to measure:
in UV I will recommend a commercial titania (Degussa P25 or an other)
in the visible, you can try hematite which BG is around 2.2 eV for bulk cristals,
in the NIR any lanthanide dopant can be helpful.
Does this answer help you?
Hello everybody As you know, due to the high cost and time-consuming of laboratory assays, like PCR, for the suspected cases of COVID-19, doing this type of investigation is not possible for all...
06 February 2021 6,122 3 View
I want to inject B16F10 cells into C57BL/6 mice as a melanoma metastases model to study the speed of metastases in different organs. I need advice about the designing of the best timeline for...
14 January 2021 3,704 1 View
Hi. In my project I need to move an object with arbitrary speed In the direction of the one of the Cartesian axes. I was wondering that if any one could help me with that. thanks
01 September 2020 5,626 4 View
Welcome Everyone, What is the main difference(s) between the two-parallel linear antenna array and rectangular antenna array in a smart antenna system? For example, a two-parallel linear antenna...
24 June 2020 2,520 1 View
The sun goes through a natural solar cycle approximately every 11 years. The cycle is marked by the increase and decrease of sunspots. The greatest number of sunspots in any given solar cycle is...
21 May 2020 5,045 8 View
These are Cutaneous Squamous Cell Carcinoma derived cell line
11 March 2020 7,344 7 View
As we know that the current leads the voltage in capacitor and lags in inductor, what is the reason of the phenomenon? As the capacitor opposes change in voltage and inductor opposes change in...
23 July 2019 8,648 7 View
Change is nature, and climate is changing. Human capacity in boosting and controlling climate change is still a debatable issue and has the scope of investigation. Whatever the level of human...
29 May 2019 9,526 17 View
08 May 2019 5,149 20 View
Sometimes we are too much optimistic. Try to ignore small problems, thinking that they have no potentials to do any harm. such thinking gives us self-satisfaction and we continue doing nothing....
27 April 2019 9,091 8 View
Hello everyone. Given microstructure image belongs to a 12% ledeburitic cold work tool steel (annealed and tempered). The sample was etched with picral (100 mL ethanol and 4 g picric acid). I...
02 March 2021 4,119 3 View
In some materials, properties such as band gap, thermal conductivity differ along different crystallographic axes. What are the basics?
01 March 2021 1,923 3 View
It is a general practice to introduce Ground Plane in FDSOI devices under the BoX. The Ground Planes are introduced by Ion Implantation through Top Si layer and Buried Oxide. I wanted to know that...
24 February 2021 5,974 4 View
Does the absorption coefficient of the semiconductor changes with the change in the structure of the semiconductor? If you have a thin film and nanowire of the same semiconductor, will the...
23 February 2021 9,799 4 View
I notice that upon washing and air-drying of my RGO/SPCE surface and characterizing again via DPV, the current response towards ferricyanide probe significantly decreases. My worry is that the...
22 February 2021 5,324 3 View
I am working on polishing abrasives. I need to do few characterizations ? which can provide the on time surface chemistry of substrate with polishing abrasive during optical polishing. I would...
18 February 2021 5,319 3 View
I have a direct band gap material and an indirect band gap material. If I made a composite of both through physical mixing. Then how can I determine the band gap of such a material as the Tauc...
17 February 2021 8,104 4 View
A new cell subtype was found out only during regeneration phases after a cuprizone-induced demyelination model. How can I characterize this cell? It is important to highlight that was already...
13 February 2021 1,245 1 View
I need to spin a 120um thick film. My current procedure consists of spinning the polymer (about 20um), uv exposure, plasma etch, and then spinning another 20um thick layer, uv again, plasma etch...
10 February 2021 2,055 6 View
I am having trouble setting up this problem in HFSS or FEKO. In HFSS, I've tried both FEM and FEBI-IE solvers. With FEKO, I've tried it's MoM solver and default settings. I am would like model...
09 February 2021 375 2 View