11 November 2018 7 3K Report

Please I'm looking for some articles or opinion about it. Thanks

More Katherine Meirama-Ross's questions See All
How to correct an article ttle error?

The following article of which I am a co-author has a word missing from the title in ResearchGate: "Authigenic formation in suboxic marine sediments" should be "Authigenic magnetite formation in...

28 January 2024 4,297 0 View

How can I remove a published paper from Research Gate and replace it with an updated paper?

see question

16 January 2024 1,316 3 View

Strongyloides or "Hookworm" (unusual presentation) larvated ova from canine faeces?

A single egg was isolated from a young dog faecal sample. The dog is showing GI signs.

02 December 2023 6,848 0 View

Best way to preserve FACS enriched cells for downstream single nucleus RNA & ATAC seq?

I am working with a cell population that needs to be enriched by cell sorting from fresh tissue. I am wondering what the best way to preserve the cells, after sorting, for downstream single...

30 October 2023 9,156 0 View

Why is my gel loading not consistent?

I loaded the 1.5% agarose gel as standard. I loaded 6uL from PCR and 1uL loading dye. Why is the solution not sinking to the bottom of the wells?

23 October 2023 3,885 2 View

My ligation troubleshooting gel has very blurry bands, what does this mean?

The first lane is 1kb ladder, the second lane is the ligation reaction, the third lane is plasmid only control. Previously the same PCR product gave clean bands but now it isn't and I don't know why.

02 October 2023 2,354 1 View

How do I decide the digestion time of PCR products?

My supervisor suggested that the bp of PCR products is related to the digestion time. I cannot find anything on the internet to solve my problem. I have a PCR product 500bp. My supervisor implied...

27 September 2023 2,889 3 View

Why are there no bands on the gel for my ligation?

I have run PCR and digestion (Not1-hf & Nde1) that gave good bands. The plasmid was PET-28-make123 and the PCR product was franken-flag-dsred. Then I performed ligation and ran a gel with...

21 September 2023 8,628 3 View

Protocols for purification of of LC-MS grade solvents?

We have recently been finding that some of our LC-MS grade solvents have impurities (several brands) - notably acetonitrile and methanol. To avoid future problems, we would like to do an in-lab...

08 August 2023 884 4 View

What number of intronic basepairs adjacent an exon would be important to look at for detecting issues with splicing/etc?

We are running a project where we are Sanger sequencing gDNA for a specific gene (DPYD), and doing sequencing reactions for each of the exons. The reads we get include intronic bp on each side of...

17 July 2023 4,886 2 View

Similar questions and discussions
Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

How do I conformally do PR spin coating on trench structure?

I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...

08 August 2024 2,298 0 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

What is the most effective way to sterilize camelina seeds?

I'm working on camelina seed sterilization and have some doubts about the process. I followed a protocol used by my lab mate, but I'm unsure about a couple of things: Is it safe to use 10% bleach...

02 August 2024 1,178 3 View

When should I stop watering A.thaliana for collect their seeds?

I have been following Rivero et al 2014 protocols, but I am not sure when I should stop watering because my plants are completely yellow but the siliques are not 80% brown. Any recommendations?...

30 July 2024 2,301 7 View

What is the reason I get 400nm nanoparticles using an extruder with 200 nm membrane for cell membrane coating?

I am trying to coat my micelles and PLGA based nanoparticles with cell membrane using an Avanti mini extruder according to literature . I use 200nm membrane but my particles end up to be 400nm And...

30 July 2024 3,294 3 View

What is the main used curing agent for epoxy based coating?

I am trying to coating metal oxide into steel substrate, for better sticking planning to utilse epoxy based, Could you please suggest suitable curing agent for the coating purpose

25 July 2024 438 3 View

How should I prevent mould contamination on small seeds in a petri dish exposed to warm temperatures?

Hello all, Recently as part of a research project at university, we have been studying the effects of light and temperature on eucalyptus seed germination. In our initial run of trials we...

24 July 2024 8,850 4 View

How do you get pure primary macrophage cell culture?

I have been harvesting monocyte-derived macrophages from buffalo and cattle fresh whole blood using the same protocol for years and getting good macrophage cultures. Below is the protocol that I...

23 July 2024 4,074 2 View

HEC 1A & HEC1B Cell Lines?

Hi, Kindly guide me that how many cells of HEC1A & HEC1B Cell lines should I seed for Wound healing assay and which plate type is recommended 6, 12 & 24?. Articles suggested mainly 24...

20 July 2024 4,143 2 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close