Questions about publishing books

More Debela Tezera's questions See All

Abaqus standard or dynamic explicitly?

Which type of ABAQUS solver is better in computional cost during sequential coupled thermomechanical analysis. With abaqus standard it's difficult to obtain converged solution.

26 October 2021 8,080 3 View

Displacement correction too large displacement increments?

In message file of ABAQUS I obtain " rotation correction and displacement correction is too large compared to rotation or displacement increments respectively. How I can solve this one.

18 October 2021 6,822 2 View

Negative system matrix?

Am stimulating sequential coupled thermomechanical analysis in abaqus standard but abaqus terminate the job when the second step is started warring system matrix have 300? Negative eigenvalues

11 October 2021 6,600 3 View

How to/ the way to score Parenting Style Scale to be grouped in to two dimensions and four categories?

Dear all Researchers in this group, please help me the way to score Parenting Style Scale to be grouped in to two dimensions and four categories. The Scale is, Parenting styles scale (PSS)...

09 October 2021 4,153 2 View

What is the maximum and minimum thickness of lamina composite layup?

Please,any body who have designs guidelines On limit of each ply thickens share it.

07 September 2021 7,059 4 View

WHat is the proplem?

Am modeling,GFRP t-up ribs concrete bridge deck but experiment and FEM doesn't agree. Because doesn't show any failure. Concrete is modeling is using CDPM GFRP rebar as isotropic only with Poison...

31 August 2021 9,695 4 View

How can correct the warring during heat transfer analysis by abaqus" heat flux equilibrium not achieved with tolerance*?

Heat transfer analysis using abaqus/standard

01 August 2021 332 3 View

I have E1 , E2, ultimate tensile strength and compressive along longitudinal and transverse direction of pultruded GFRP T ribs,how can model it?

Am modeling it for thermal and structural analysis

01 August 2021 2,531 2 View

1.How can put nodes on equal distance in WSN? 2.How calculate retransmission of each node in WSN? 3.How to create buffer for each node?

I am using matlab simulator and doing paper selfish node detection based on average retransmission number. Some factors determine selfish node in wsn -If energy is not sufficient to forward...

28 December 2020 7,550 2 View

Which routing protocol is suite in selfish behavior of node detection in WSN based on average retransmission number?

Dear all; As you know we have many types of routing protocol on WSN. Among these which routing protocol is best for my thesis title? please help me with best regards

03 December 2020 9,110 3 View

Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,563 0 View

Hello Everyone ! I'm looking for a good journal to publish my manuscript with low publication cost?

I am Looking for a Science Journal with good impact factor and low publication cost to publish a review paper. Your suggestions would be appreciated.

06 August 2024 6,796 3 View

Is an invitation to join the editorial board of Clinical Cardiology Updates a scam?

I received an e-mail invitation to join the editorial board of Clinical Cardiology Updates. While I have published a few articles related to cardiovascular disease, there are lots of colleagues...

06 August 2024 8,981 8 View

Why is the Protocol for Preventing Postpartum Hemorrhage (https://pubmed.ncbi.nlm.nih.gov/36113283/ ) not being widely adopted?

If the placenta is delivered in squatting position within 3 minutes of the birth of the baby, postpartum hemorrhage is completely eliminated. It works every time. It is quite likely that if a...

05 August 2024 8,895 0 View

Do you know any references for analyzing stochastic fiber orientaion composites ?

Hello everyone I am looking for one or some books for propertes and behaviors of stochastic fibre orientation composites. unfotunately I could not find any suitable reference for thias by...

04 August 2024 3,461 3 View

How do i get an account to upload my published papers?

need to open an account to upload my published papers

01 August 2024 9,255 1 View

About impact factor?

I have been publishing the Nepalese Journal of Agricultural Sciences (online ISSN 2091-0428; print ISSN 2091-042X) on www.nepjas.com and research gate. I was wondering how I can get an impact...

01 August 2024 1,277 1 View

Are you interested in contributing a book chapter on biomaterials in Orthopaedics?

I am editing a book for Springer Nature on recent advancements and future trends in biomaterials for orthopedic and trauma applications, with a publication date slated for early next year. If you...

29 July 2024 5,015 9 View

"Idrisi Selva" tutorial Books for pridiction with driving factors in modeling?

Some educational books with practical exercises of the "Idrisi Selva" software, which have step-by-step visual training for predicting the change of land use/land cover and including the use of...

28 July 2024 4,168 0 View

Publish a Protocol?

Hi, please suggest some journals where I can publish a observational study protocol.

27 July 2024 2,519 0 View

Stephen Lynch

In order to have a book published, you need to contact publishers (Springer is probably the best for academia). They usually require a Preface, Table of Contents and one or two completed chapters. You then need to explain how your book is different to all other similar books (you need to list them) and state why your book will sell copies worldwide.

Ian Kennedy

DON'T use LAP LAMBERT MACADAMY