Problem during Compilation - DFLUX Subroutine in ABAQUS?

27 September 2021 1 2K Report

I'am trying to do a Heat transfer simulation in abaqus.

I have sucessfully passed the verification check and the link between fortran compiler and abaqus is established, and further verified as the UMAT subroutine is working.

Has anyone experinces that only the DFLUX is causing compilation errors?

Simon Smith

Hi Kenneth,

Have you tried putting the DFLUX code in a file and compiling separately from an Abaqus analysis? There will be some predictable errors because the code is a subroutine alone, but you may also find some other errors. This might help to debug the code.

Regards,

Simon

Badges
Science topic

More Kenneth Meinert's questions See All

What recipe of homemade lenti-virus concentrator do you use?

My lab is using a lenti-X concentrator. And we are looking for a homemade recipe. I have tried this recipe....

08 February 2021 5,965 1 View

What are the parameters that plays a role in life-time degradation models of concrete? what are the most important tests to measure these parameters?

I'm working on a research about the prediction life-time models for concrete in harsh environment. I have to answer those two questions.

14 November 2020 2,043 7 View

Does anyone know of historic sites that have artist in residency programs?

A research assistant and I are conducting primary research on artist in residency programs (artists, writers, etc.) and the use of contemporary art at historic sites to reinvigorate or...

27 September 2020 9,355 4 View

What is PROSPERO - University of York regarding Systematic Literature Reviews?

I have seen for the first time a systematic literature review and meta-analysis that has prospectively registered their review in PROSPERO and I am wondering what is the main reason for creating...

04 August 2020 4,167 4 View

What causes the copy detection limitation in PCR?

Hi all, I wish to understand why doesn't all polymerase can detect a single copy of region of interest? While some polymerase is more sensitive (like dreamtaq), and some are less sensitive, what...

02 June 2020 4,397 21 View

Evidence-based resources for helping kids cope with debilitating & likely fatal disease?

A colleague asked me for any evidence-based approaches to helping kids (and parents) cope with a life-threatening disease, Duchene muscular dystrophy. The child doesn't know he is sick yet. Does...

24 March 2020 2,046 3 View

Does anyone has experience with NEB "time-saver enzyme" overnight digestion?

Hi all, I used the Thermo-ANZA series for overnight digestion of plasmid backbone to ensure clean digestion without any problem. How about NEB? The website said all NEB "time-saver enzyme"...

24 March 2020 7,636 2 View

Difference between cell culture plates and flasks?

In the lab we always use culture plates (33, 60, 100, 150mm) for passing cells and conducting all sorts of experiments. I wonder what is the perks of using cell culture plates v.s. flasks? Should...

12 March 2020 1,361 2 View

How can can I find a none fee charging credible journal to publish a co authored paper?

I am looking for a none fee charging journal to publish a coathored paper. Its in special education

20 January 2020 5,203 3 View

Can I transfer Spheroid to normal attachment plates for other assays? How will it affect the morphology and consistency?

Do you guys have any experience in transferring spheroid produced in low attachment plate to a high attachment plate after spheroid production? Would it affect the morphology of the spheroid? I...

11 December 2019 1,918 3 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

What are the countries most affected by extreme rainfall as a result of climate change?

Increased heat, drought and insect outbreaks, all associated to climate change, have increased wildfires. Decreasing water supplies, declined agricultural yields, health impacts in cities owing to...

01 March 2021 7,168 9 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

How to assign different material properties to each element in Abaqus ?

Hello, I am writing a python script to generate my model and write the input file. The problem is I have 1000 elements in my mesh and I want to assign different material properties to each...

01 March 2021 9,511 3 View

Heat exchanger with liquid Nitrogen as coolant?

I want to cool Natural Gas from 195 Kelvin to 138 Klevin in a heat exchanger by using liquid nitrogen as the coolant medium. When entering the heat exchanger, the liquid nitrogen will have a...

01 March 2021 6,450 5 View

How to define tie constraint between rigid body and another part in dynamic explicit model of Abaqus?

Hi dear researchers I connected a rigid body into the part of my structure by tie constraint and then I added displacement to rigid body, in static general step every thing is fine and these two...

28 February 2021 3,442 2 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View