Preparing 3D model for relationships between 3 explanatory and 3 response variables using Response Surface Methodology (RSM). Any Video tutorial link?

01 January 2016 1 4K Report

I am preparing 3D model for relationships between 3 explanatory and 3 response variables using Response Surface Methodology (RSM). Any Video tutorial link?

Sanjoy Roy

hahahah, Emran, Use JMP/Sigma Plot.

Badges
Science topic

More Al Emran's questions See All

Is there any online free course on planetary photometry (or photometry)?

Is there any online free course on planetary photometry (or photometry)? Pls, send me the link. Thanks!

10 November 2019 10,242 1 View

Image Fusion/ Pan Sharpening?

Is there any method by which I can sharp or enhance a 100 m/pixel single band image with another 6 m/pixel single band panchromatic image? (FYI: Both images are single band). Thank you!

31 December 2018 7,797 6 View

How can I calculate "Weighted Absorption Centre(WAC)" at pixel level from multi-spectral image using ENVI/ ERDAS/ QGIS etc.?

Hello, Can anyone tell me how can I calculate "Weighted Absorption Centre (WAC)'' at the pixel level in multi-spectral data using ENVI/ERDAS/QGIS/E-cognition?

03 April 2018 2,445 2 View

How can I run IDL source code with my interested image?

Hello, I have an IDL source code for a particular satellite image processing. Could anyone pls let me know how can I run this code with my interested satellite image? Any video tutorial? Thank you!

31 December 2017 6,447 2 View

Aerosol Optical Depth (AOD) over small areas?

I would like to measure aerosol optical depth (AOD) or total aerosol contents over a small area (1.5 sq km). Pls let me know if there any sensor retrieves aerosol data for such a small area (fine...

08 September 2017 8,254 2 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

How to learn more about SPSS and its Application?

I would like to learn more about SPSS and Its application especially in regards to data analysis. Please suggest me how I can learn more about it. Thank you so much.

11 August 2024 9,101 4 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

If we are using snowball sampling technique, how do we justify the true representativeness of the sample statistically? is there any statistical test?

Are there any statistical methods to justify your sampling technique using SPSS or AMOS?

05 August 2024 9,153 4 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View