Please discuss about the algorithm or method that can be used to optimize tapered pile angles and share your experience and research .

01 January 1970 1 3K Report

If you are researching about the optimization of concrete piles. Please discuss about the results of your research and the best method and algorithm that can be used to optimize tapered piles angles.

M.R. Pordel

Thank you very much for your answer and guidance .

Badges
Science topic

More M.R. Pordel's questions See All

Comsol electromagnetic simulation. How to give a mesh for certain micrometer when my tool is in millimeter. The current density is so small. Pls help?

Hi, I am trying to perform mesh convergence and I found out there is no stable temperature value I obtained. So, I calculated the skin depth and it was around 0.00011mm. It is so small in...

24 August 2020 9,060 2 View

How to model in COMSOL (Induction heating) . A current applied for 600A for 10 min and continue then 100A for next 5 min. Can someone help me please?

Hi I wanted to model Induction heating in comsol. Apply a current of 600A for 10 minutes in my coil and then a 100A current for 5 minutes. I could not find much of tutorials. I do not know where...

10 April 2020 5,565 12 View

Where i can get the electricity price for different EV agents?

Hello, i hope you all are good. i am modeling a system for charging and discharging cost minimization for different EV (Electric vehicle) agents like households, business...

27 November 2019 5,599 4 View

How to plot Basin of attraction for coupled maps in MATLAB?

1) I am trying to plot the Basin of attraction for 2d discrete dynamical system in MATLAB. Please give some suggestions to get them. 2) If possible, give some simple example like...

08 November 2019 5,668 3 View

Thermal topology optimization run ends with error due to memory. How to swap memory?

Hello. I had a run error *7007* that the allocated memory is 17,500 Mb but the run for the model required 18,400 Mb. When i check my directory file, there is more memory around 1TB and the system...

06 November 2019 8,994 3 View

How to make the displacement value show up?

Hello all, I need a help really. I have displacement at a point as in the image where it shows Mag = 0 and Z = 0. Apart from static min and max. That nodal point on top I needed the values. Since...

03 October 2019 3,670 3 View

How to make a flat surface in ANSYS or HM. Can someone suggest me?

A bracket has been analyzed and the solid is not flat. The triangular elements are bumpy on 2 sides of the bracket and I want it to make it flat before I re-analyze for static displacement and...

16 September 2019 3,885 3 View

Which one is the best protocol to measure aggregate stability ?

Need reviews regarding measurement of aggregate stability.

14 March 2017 9,709 2 View

Does anyone has idea about recent data regarding acreage of various fodder/forage crops in India?

Current statistical data on acreage of different forages in India.

14 March 2017 5,084 2 View

How can I measure the N fractions in rhizospheric soil samples?

Please suggest me the precise and standard methodology to compute the various N fractions in rhizospheric soil samples.

09 March 2017 6,447 6 View

What is the procedure to determine the permeability of concrete?

can anyone help me in this, it will help me with my research work

01 March 2021 834 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Apart from Nanosilica and CNT's what are the other nanomaterials readily available to use in concrete mixture?

Nanotechnology in concrete materials

01 March 2021 3,379 3 View

Concrete compressive strength databases?

I am looking for datasets similar to this one: http://archive.ics.uci.edu/ml/datasets/Concrete+Compressive+Strength I am looking for concretes with different types of aggregates (Recycled,...

27 February 2021 6,801 3 View

LEDs on Vis Light photo degradation of MB water sol via N doped TiO2 in a mini flume?

Good day to all, I have no experience with light emitting diodes. I am building a glass mini flume to demonstrate the photo degradation of Methylene Blue in water running over self cleaning...

26 February 2021 4,026 5 View

What is the best way to calculate the angles of twist for concrete columns subjected to torsional moment using finite element software?

In Finite element software like ANSYS , there is difficulty in obtaining direct results of twisting of concrete members because SOLID65 which is the unique element designed to represent concrete...

26 February 2021 3,806 2 View

Compute for the total volume of concrete needed for the concrete pouring of the foundation including its column up to NGL only as shown in the plan?

Looking for the quantity of cement, sand, and gravel of footings and columns. Thank you!

25 February 2021 3,092 2 View

Best FE Program for Concrete Strengthened with FRP Sheets?

Colleagues, I have been using ANSYS to model concrete strengthened FRP sheets, but less than happy with it. Any has recommendation for efficient, easy to use FE program for modelling concrete...

22 February 2021 7,528 3 View

Is there a Constitutive model for concrete with Sea-Sand?

Hi I am running a simulation in Abaqus for a concrete beam. Its fine aggregate replaced with sea-sand. I was wondering if I could find studies that measured the ultimate strain of concrete made...

22 February 2021 6,409 2 View

How to overcome convergence issues in concrete arch models?

Hi, I have modelled a three-span arch bridge with soil fill over along with pedestals. The FE modelling is done in LUSAS with HX8M solid elements (i.e. 3D solid modelling). The non-linearity is...

20 February 2021 1,346 2 View