Photoluminescence setup of liquid samples?

Sara Ghayeb @Sara_Ghayeb

11 November 2016 0 7K Report

Dear researchers

is there any difference between photoluminescence setup of thin film samples and liquid samples?

for thin film samples, reflection is important. what about liquid ones? does scattering dominate reflection?

Badges
Science topic

More Sara Ghayeb's questions See All

Excitonic peaks of MoS2 in C/MoS2 composite?

Dear researchers Can anyone tell me the effects of carbon nanoparticles on the excitonic peaks of the MoS2 nanosheets in C/MoS2 composite?

31 December 2018 7,463 1 View

Color of the exfoliated MoS2?

Dear researchers I'm trying to prepare liquid-phase exfoliated MoS2 in various solvents. According to the literature, the green-yellow color of the dispersion is a good indicator of the exfoliated...

08 September 2017 7,415 5 View

Material with high optical absorption at 1064 nm?

Dear researchers Can anyone suggest me a material with high optical absorption at 1064 nm?

31 December 2016 7,538 5 View

95Mo NMR analysis??

Dear researchers I need to perform 95Mo NMR analysis. Is there anyone who knows where I can have it done?

11 December 2016 1,026 0 View

Band gap energy calculation of the exfoliated MoS2 nanosheets?

Dear researchers Is it possible to use Tauc equation for the band gap calculation of MoS2 nanosheets? I haven't seen it yet in the literature. is there any alternative way?

08 September 2016 4,773 9 View

What is the solvent of graphene oxide?

I want to clean the residual graphene oxide inside a quartz cell. what is the best solution?

07 August 2016 3,312 4 View

What does the FWHM of a peak in RBS spectra show?

31 December 2013 5,389 1 View

Which one has the highest photocatalytic activity, amorphous WO3 or monoclinic WO3?

11 December 2013 1,485 3 View

What are the photocatalytic reactions of Methyl Orange decomposition by TiO2?

Is Methyle orange acceptor or donor? Which one of photo-induced charges (electron & hole) participates in Methyl Orange decomposition?

11 December 2013 5,753 4 View

What information does a SEM map give us?

How can we interpret it?

11 December 2013 3,923 17 View

12% ledeburitic cold work tool steel, etched for revealing retained austenite, any help for clarifying?

Hello everyone. Given microstructure image belongs to a 12% ledeburitic cold work tool steel (annealed and tempered). The sample was etched with picral (100 mL ethanol and 4 g picric acid). I...

02 March 2021 4,119 3 View

Is There Any Feasible Method To Test Fluorescent Compounds Other Than Fluorescence Spectrometers ??

Is There Any Feasible Method To Test The Efficiency Of Fluorescent Compounds Other Than UV Spectrometers ? Suggestions Would Be Appreciated !

02 March 2021 5,785 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

Why initial concentration of Pb not the same as calculated one when testing using AAS?

I am currently doing research on the adsorption of heavy metal using magnetic reduce graphene oxide. I use AAS to determine the concentration of the heavy metal. I prepare the Pb solution with...

26 February 2021 9,580 4 View

LEDs on Vis Light photo degradation of MB water sol via N doped TiO2 in a mini flume?

Good day to all, I have no experience with light emitting diodes. I am building a glass mini flume to demonstrate the photo degradation of Methylene Blue in water running over self cleaning...

26 February 2021 4,026 5 View

Can anyone share his experience regards Smoothing in origin?

I am working on TiO2 composite material and the results of XRD have a lot of small/junk peaks and while I apply a smooth filter in Origin then the other characteristics peaks disappear so anyone...

26 February 2021 8,183 3 View

I am looking for a simple software program to model 3D chemical bonds. The purpose is to generate high-quality graphical abstracts. Any suggestion?

Hello everyone: I am looking for a simple software program to model chemical bonds. The purpose is to generate a high-quality graphical abstract for a top leading journal in the field of...

23 February 2021 8,012 3 View

Is this the write procedure for acid digestion of soil for heavy metal analysis using AAS?

How to do acid digestion of soil sample with 3:1 aquaregia in an open vessel?

23 February 2021 3,053 7 View

Is there an ideal incubation time of RGO-modified SPCE before subsequent use, i.e., electrochemical characterization or further modification?

I notice that upon washing and air-drying of my RGO/SPCE surface and characterizing again via DPV, the current response towards ferricyanide probe significantly decreases. My worry is that the...

22 February 2021 5,324 3 View

How we can measure Kemp % in wool without using of benzene?

Would you please let me to know about the methods for measurement of medullation and Kemp % on animal? My problem is that the wool sampling and sending to laboratory is not possible. So I would...

21 February 2021 7,260 4 View