Parallel execution of the MCNPX ?

30 August 2023 1 7K Report

Hi Dears,

What is the alternative to the ctrl+C command in the parallel execution of the MCNPX code?

Ruhollah Adeli In the parallel execution of the MCNPX code or any other command line program, the Ctrl+C command is typically used to send an interrupt signal to terminate the program. If you're looking for an alternative way to stop MCNPX when it's running in parallel, you can consider this alternative :

kill -9

pkill name

More Ruhollah Adeli's questions See All

Dear friends,

when i run a program in MCNP code which contans repeated structure, I confront with a message: bank is full. bank backup file is being created. How can i overcome with this problem?

08 August 2017 5,778 6 View

How to code open-ended questions in SPSS?

Hello all, In SPSS I am going to code 2 open-ended questions. I have already read all the answers and I made a list of the most important categories to which I can code the answers. This question...

02 March 2021 1,757 4 View

How to model the battery pack in PSIM or PSCAD?

Hello, I have simulated a single battery cell using Thevenin equivalent circuit. For a battery pack, I have a large number of cells connected in series and parallel connections. Is there any way...

28 February 2021 2,116 1 View

How to eliminate Steady state error from Reinforcement learning genetic algorithm code?

The following code (see 1st 2 images attached) is used to produce PID controller values that are designed to control the system (G). The code finds the PID controller values (noted as k) by using...

28 February 2021 6,560 14 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

How could I process data in RCT to include it in meta-analysis?

I'm in the process of doing a meta-analysis and have encountered some problems with the RCT data. One of my outcom is muscle strength. In one study, I have three different measurements of muscle...

25 February 2021 7,603 3 View

Modeling viscosity using model of Chung?

Hello, As part of simulation of gases mixture and water, I need to calculate viscosity of the fluid components and I am using relationships proposed by Chung et al. (1988). The irony is while I...

25 February 2021 8,053 5 View

Satellite orbit estimation using Recurrent Neural Network - what should I use?

Hello, I am a master's student studying in Yonsei Univeristy, Korea. I am trying to estimate the state of satellite, using Neural Network. Below is a simple flow of my study. 1. Train (t0 ~ t1)...

23 February 2021 6,383 3 View

Any Differences in COVID-19 vaccines?

Are there any differences (outside of the clinical trials that led to their EUA) observed in the rate of infection among those who have received the Pfizer vs Moderna vaccine since the mass...

22 February 2021 9,727 6 View

How can I get the coding gene sequences of Hela and U2OS cell lines? Is mRNA sequence of Hsp90 alpha tissue specific??

I am looking for hsp90 mRNA sequence in Hela and U2OS cell lines, I have tried through ncbi but always the output is hsp90 in homo sapiens not in the specific cell line. Kindly, could any one...

22 February 2021 1,853 3 View

How to constrain genetic algorithm input u?

My real system (buck converter) can only take an input of 0 to 1 (duty ratio) and I need to constrain the system so the controller action keeps within this bounds. How can I do this? The code for...

22 February 2021 2,125 3 View