How to avoid spreading of alpha in interFoam?

For my thesis I need sharp interface between gas and liquid. But I'm getting a a transition layer between gas and liquid. Can any one tell me how to avoid this problem. Please

08 September 2017 4,940 3 View

Regarding the flux calculation in OpenFoam?

08 September 2017 948 5 View

How to initialiaze a scalar field in a steady solution OpenFOAM?

Hi Foamers, I have a steady flow field solution available using interFoam. I wanna use this steady solution for further simulations.How can I initialize a scalar field in liquid phase (scalar...

08 September 2017 8,921 3 View

Mass transfer from one phase to another in interFoam?

Hi Foamers, How can I model mass transfer from one phase to another in interFoam . I don't have a phase change , rather I have absorption of gas into the liquid. Regards, Phanindra

08 September 2017 9,756 3 View

How to find the cell distance from a patch in openfoam?

Hi foamers, can any one of tell me how can we find the distance between an internal cell from an inlet in openfoam I need to use it as part of my code not as post processing Regards, Phanindra

08 September 2017 5,893 2 View

Liquid film thickness

Hi friendsCan any one of you tell me how to find liquid film thickness over a flat plate in paraFoamI was able to generate an iso surface for liquid film but I'm struggling to find its distance...

05 June 2017 7,490 1 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

After a reference from Int J Body Compos Res, can any body help?

Hi, I am after the reference below, my library says it cannot obtain a copy either locally or internationally, any help appreciated! Chris Wang ZM, Heshka S, Wielopolski L, Pi-Sunyer FX, Pierson...

03 March 2021 6,193 1 View

What techniques can I use to determine the miscibility of polymer blends?

The term miscibility refers to the single-phase state in thermodynamics. I do not mean the compatibility of different components. To determine the miscibility I know several techniques such as...

03 March 2021 4,107 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View