Is there any thin, flexible conducting wires capable of current carrying of around 0.5-1.0 Ampere?

I want to use connecting wires for the soft robot to deliver electric current of around 1 A (voltage 5V), however currently available wires are quite rigid and they exert negative force for the...

05 January 2021 4,485 3 View

A three electrode sensor inkjet printed gets damaged in few hours of usage in a dynamic media flow chip, any solution for that?

We are using some biosensors which are inkjet printed and are used in the microfluidic chip where media is flowing at the flow rate of around 60 uL/min. However, after the continuous use of few...

05 January 2021 610 2 View

USB based DAQ options with atleast 4 analog output channels and 8 analog input channels other than National Instruments?

National Instruments provides vast variety of DAQ options which are based on LabVIEW, however they are way too expensive when it comes to opting option with high analog output channels (like 4)....

30 August 2020 5,195 6 View

What could be direct/indirect roles of insects (entomology) in current pandemic COVID-19?

Because there is no any vaccine for COVID-19 until and in past insects have transmitted number of diseases like; chikungunya virus, yellow fever, dengue fever,Lyme disease, plague,malaria,...

24 June 2020 9,557 30 View

Automatic Save STARCCM+: Warning ''Insufficient space on the disk''?

Hi Everyone, While running the simulation, I kept the file on ''Autosave'' so that each time step is saved (to avoid loss of data due to internet disruption since I am using VPN) but after 1-2...

13 May 2020 7,645 3 View

Where to purchase flexible connecting wires for soft actuators?

Normal wires (for providing voltage) to soft actuators behave as an obstacle to the actuators and hence the real response of designed soft actuators is not known. can you please share the online...

13 November 2019 5,602 1 View

How to classify a text in to different categories without predetermined labeling?

I want to classify a text of more than 1000 words into a categories. I have a database of 10,000 reports of which each contain more than 1000 words. I want to classify them and would like to know...

04 October 2019 1,554 5 View

Any temperature sensor (other than probe type) reported in Microfluidic system or organ on chip?

Normally, I have seen the commercial temperature sensors of probe type are used for microfluidic or organ on chip platforms. I am looking for any paper in which temperature sensor is reported to...

30 May 2019 7,293 4 View

Why are stator currents flowing during stand by mode on flywheel energy storage system?

Hello everyone, I am working on Induction machine driven flywheel storage system. I am facing problem with stator currents. There are stator currents of the magnitude 10-20A during standby mode of...

11 February 2019 6,868 5 View

Is there any way to cure the collagen for making thin membranes?

collagen is commercially available in liquid as well as in fibrils, is there any way through which we can cure and make a thin layer like membrane using collagen?

16 September 2018 1,444 3 View

PScad compatibility with SIMULINK?

Hello, I tried to perform a co-simulation between PScad and SIMULINK. I reviewed the requirements of compatibility between them but I still have no clue about this issue. My PScad is 4.6.3 (x64),...

06 January 2021 8,226 1 View

PI controller Tuning?

Does anyone have any expertise in PI controller Tuning for HVDC model? PSCAD Model is up and running and requires PI controller tuning to achieve the parameters

12 June 2020 803 3 View

How i can Simulate a PV Control System in PSCAD?

I need a book, chapter or something like that which discusses PV inverters. It explains Mathematical relationships and finally Simulates it.

13 April 2020 7,157 6 View

How do I enter multiple points of I-V MOV characteristic from an external file in PSCAD?

I have a multiple points from a I-V MOV characteristic from a equipment datasheet, but PSCAD only allows to enter eleven points. I saw there is an option to enter until 100 points from an external...

28 February 2020 2,737 3 View

MOV modelling using PSCAD?

What are the main parameters that should be entered in pscad for MOV modelling? The MOV will be part of the overvoltage protection circuit of a series capacitor in a transmission line. And how do...

27 February 2020 2,055 2 View

How to prove the stability of the controller mathematically without knowing the transfer function of the system?

The circuit is shown in the attached picture, It is difficult to find the transfer function right know .In the figure Ictrl is the dc current coming after thyristors switching and Irms is the rms...

05 September 2019 10,008 4 View

Thyristor 6-pulse rectifier working as a 6-pulse diode rectifier (even in light load/discontinuos conduction mode)?

For a thyristor based 6 pulses rectifier, is any open/closed loop control/firing-strategy that permits to match the behavior of a 6-pulse diode rectifier? The answer is not just "set alpha=0",...

04 April 2019 4,686 2 View

Thyristor 6-pulse rectifier working as a 6-pulse diode rectifier (even in light load/discontinuos conduction mode)?

For a thyristor based 6 pulses rectifier, is any open/closed loop control/firing-strategy that permits to match the behavior of a 6-pulse diode rectifier? The answer is not just "set alpha=0",...

03 April 2019 8,969 2 View

Can we model or control microgrid using MATLAB Coding ?

02 March 2019 6,836 3 View

What is the mathematical formulation of BIomass cost function?

i am trying to formulate an Economic Dispatch of HVDC transmission with Renewable energies...But unable to come up with biomass cost function. please help

26 January 2019 212 1 View