Need Template or type setting option to publish in Wireless Personal Communication ?

More Mageshwaran Subbiah's questions See All

What is the updation of billet sawing machine in cutting process of modern manufacturing?

The billet sawing machine thus enables to cut two rods at the same time in order to reduce the cutting time and also could be improved 50 to 75 % (approx.) of the productivity in modern...

14 November 2019 9,899 1 View

Productivity enhancement of solar still by How Phase Change Materials (PCM) and Nanoparticles important in Solar energy based Water purification?

Belongings of incorporating (Al2O3) Nanoparticles of wick materials in the solar still of a PCM charity in the basin for TES organization have been probed. It is an innovative organization of...

22 March 2019 5,282 4 View

What is coordinate measuring machine (CMM)? How is it important in Metrology of Manufacturing Industries?

The coordinate measuring machine (CMM) is a mechanical system that moves a measuring probe to determine the coordinates of points on the surface of a work piece. The CMM comprises: the machine...

01 March 2019 9,027 2 View

What are the important of Magnetorheological Abrasive Flow Process in Manufacturing?

Modern advance finishing process in machining Process also having qualified reduction of tool resistance condition limitations i.e. in EDM, ECM, USM, AJM etc. cutting edge relative motion with Pre...

27 February 2019 2,392 3 View

How Scanning Electron Microscopy (SEM) very useful in Metal Matrix Composite?

The Scanning Electron Microscopy (SEM) is very useful to study the worn surfaces of the proposed specimen (eg. Al-SiCp) composites and carryout the tests to learn the effects of sliding distance,...

12 February 2019 3,476 10 View

How ethanol and ethanol-isobutanol act a fuel additive in an I.C Engine to improve Engine performance?

While Using ethanol and ethanol-isobutanol as a fuel additive to unleaded gasoline causes an improvement in engine performance and exhaust emissions.

07 February 2019 8,282 2 View

Is there any updated list of predatory journals/publishers available on the Web (like Jeffry Beall's)?

How one can find out the list of predatory journals/publishers (like Beall's list)?

11 March 2018 5,954 3 View

Do we need to write protocol for a second study of a systematic review that has been registered and published?

I have conducted and published a systematic review and meta-analysis research with the topic related to public health and health pomotion (protocol was registed in PROSPERO). Now we want to...

03 March 2021 8,920 3 View

How to upload pdf of my articles published?

03 March 2021 2,183 3 View

Would adding books published in Lambert Publishers increase my RG impact?

There are some books published in LAP. Shall I add it to the RG?

02 March 2021 2,753 1 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

Is Journal of Agricultural Research a predator?

it is published by Juniper

28 February 2021 354 4 View

How can I publish a manuscript in free or low cost journal with good H-Index?

Dear all I am going to publish my manuscript which is from my thesis in a good H-Index journal but I found them very expensive(I don't have financial support) based on the exchange currency of my...

28 February 2021 7,800 6 View

How to improve and implement WBAN MAC and Radio modules under Castalia 3.2 ?

Hello researchers, Hello Castalia3.2 researchers I am a beginner with Castalia, I work on optimization of RFID systems used in wireless body networks. I simulated a WBAN with 10 nodes and one...

28 February 2021 400 1 View

Which software is better to write systematic review paper?

We have seen some authors use some software to write review paper. As obvious, the study of all published papers concerning our studying field is not possible and these software can help us to...

27 February 2021 6,296 1 View

Can I put a figure that was drawn by Bio-Render in publication paper?

I want to publish paper in journal but I have figures which have drawn with bio-renders, can I put them in the paper or which other software I can use to draw them?

27 February 2021 8,179 1 View

Can anyone please help me in processing SAR SLC data to generate interferogram using SNAP?

I have two scenes of the study area, one top and the other bottom. As per the tutorials and papers published, the step include coregistering the master sand slave images. However, when i try to...

24 February 2021 6,372 1 View

Rob Keller

Dear Mageshwaran Subbiah I would say just follow the instructions given here: https://link.springer.com/journal/11277/submission-guidelines and ignore the LaTex template comments (apparently their is no Word template).

Best regards.

Mageshwaran Subbiah

Rob Keller Thanks for your time and guidance Professor