HOW TO Model concrete deck on CFST Beams?
This depends on the software that you use in modelling.
dear Mohannad,
i may be using Abaqus
Does A corroded steel part effect the entire concrete structure eventually ?
06 July 2018 1,062 5 View
How to adapt building and cities for climate change?
06 July 2018 9,566 4 View
I heard Chicago fire department cooling one of the steel bridges increase clearance under the bridges in downtown due to hot weather is that possible ?
06 July 2018 6,384 3 View
The choice of material in bridges are often steel or RC concrte which one would you prefer ?
06 July 2018 9,336 6 View
what are the applications of nanotechnology in civil engineering and structural engineering?
06 July 2018 3,330 5 View
1_ increasing the slab thickness 2- using drop panel 3- using shear reinforcement 4- increasing the concrete compressive strength:
06 July 2018 634 11 View
1- steel jacket 2- CFRP jacket 3- GFRP jacket 4- Enlarging the section concrete & steel cage?
06 July 2018 9,322 2 View
Placing Concrete in Hot Weather Caution needs to be applied when placing concrete in hot weather what are they?
06 July 2018 4,277 14 View
what are the common Methods for Repair of Small and Large Cracks in Concrete?
06 July 2018 7,609 2 View
What are the applications of concrete fillled steel tube truss.?
06 July 2018 6,144 3 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...
06 August 2024 9,986 2 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...
05 August 2024 3,665 0 View
I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...
03 August 2024 6,028 4 View
