Modelling of 1 horse power Induction motor, tublight of 40W in Matlab Simulink Environment?

More Shafquat Hussain's questions See All

SIngle phase Induction motor matlab simulink model?

I need a Matlab Simulink model of single phase induction motor ? Can anyone help me in this regard?

31 December 2018 5,003 4 View

Worst Case Operating Points for Inductor, Capacitor and Semiconductor Design ?

Hi I am going to design a bi directional non-inverting buck-boost converter but I have one question related to that. The question is: (1) What are the worst case operating points for that...

06 July 2018 7,705 0 View

Calculation of Inductance "L" for non-inverting Buck-boost Converter and calculation of Geometrical Constant "Kg"?

Hi Please help me designing Saturating Inductor filter for non-inverting Buck-boost converter. My questions are : (1) Is my calculation of Inductance is correct for required deign of inductor...

06 July 2018 9,747 0 View

Matlab Simulink model of Average Current mode Control of Boost converter ?

Hi everyone can anyone help me designing average current mode control of boost converter. I have design the circuit in MATLAB simulink but Output voltage is not coming the exact value . Please...

04 May 2018 2,403 5 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

No title

I am trying to find how to know the density needed for a pva electrospinning in a 0.6mm neddle, the electrospinning will be from top to bottom and the problem I really have is the solution because...

25 February 2021 2,615 3 View

How does an AC-DC power supply Flyback Converter Based USB Charger Model using Matlab/Simulink looks like?

I am required to learn about Flyback converters and I got stuck not knowing to full design of the power supply flyback converter Based USB Charger Model using Simulink, especially the design model...

25 February 2021 5,435 2 View

How Can I clain a removal of a co-author?

I would like to make a correction in a co-author in your paper which is wrong. This name is also in other papers of Kenton Ko. Zey Ko is not a Co-author . The correct name is Zdenka...

24 February 2021 3,476 4 View

How does the injection volume impact LLOQ and ULOQ in regression analysis (LC-MSMS)?

Hello, I have run into an issue that has sparkled a debate at work: is the LLOQ/ULOQ impacted by injection volume under the following circumstances: 1) Same dilution factor of all samples 2)...

23 February 2021 9,159 3 View

In frequency domain alpha band(8-16hz), beta band(16-32hz), gamma band(32-64hz), sub-band(64-128hz) are same as LL,LH,HL,HH in wavelet decomposition?

I am working on single trial motor imagery data i.e. EEG data. I am following a paper which has a dataset from BCI challenge IV (dataset 2b). After removing noise and extracting all the data from...

23 February 2021 5,503 1 View

Suppose we have a banana seller cart consisting of 4 wheels, weighing about 300 kg. How much torque motors are needed to pull of push it electrically?

I am thinking of electrifying the street food carts while harvesting energy using solar panels on top.

22 February 2021 4,323 3 View

Difficulty in debugging code to correct error - TypeError: '<' not supported ?

I am trying with a Unet code ontained from net ...in tensorflow. When trying to predict the segmentation result with the trained and saved model with metric " iou" using "CustomObjectScope"...

22 February 2021 5,254 1 View

How to build fouling and erosion simulation model for Aero Engine compressor and turbine rotor in Simulink / Matlab?

22 February 2021 3,697 1 View

How can I get "Matlab/Simulink model for Droop/Reverse Droop controllers"?

Dear Professors, Colleagues and Friends I need to develop a simple Matlab/Simulink model of reverse droop controller for a simple LV MG. How can I get a simple one to use it as a sample? A basic...

22 February 2021 8,647 2 View

Rohith Sangineni

You cannot represent a tubelight with just a resistor.If you consider an old tube light with choke, the inductance of the coil needs to be added and if you consider an electronic tubelight, you need to consider the electronic ballast circuit.

DJILANI KOBIBI Youcef Islam

have you consider other software , because your simulation is not that complicated, you can use ETAP for example it has every model of motors or light bulbs,