Worst Case Operating Points for Inductor, Capacitor and Semiconductor Design ?

07 July 2018 0 8K Report

I am going to design a bi directional non-inverting buck-boost converter but I have one question related to that. The question is:

(1) What are the worst case operating points for that converter.

(2) worst case operating points for inductor ( state Vs, Vout, Iout)

(3) worst case operating points for capacitor (state Vs, Vout, Iout)

(4) worst case operating points for semiconductor (Vs, Vo, Iout)

Thanks

Badges
Science topic

More Shafquat Hussain's questions See All

Modelling of 1 horse power Induction motor, tublight of 40W in Matlab Simulink Environment?

Please guide me I want to design a domestic load of Induction motor of 1 horse power, and tube light of 40W. I just want to ask you that is my designed model is correct or need modifications?...

31 December 2018 7,519 2 View

SIngle phase Induction motor matlab simulink model?

I need a Matlab Simulink model of single phase induction motor ? Can anyone help me in this regard?

31 December 2018 5,003 4 View

Calculation of Inductance "L" for non-inverting Buck-boost Converter and calculation of Geometrical Constant "Kg"?

Hi Please help me designing Saturating Inductor filter for non-inverting Buck-boost converter. My questions are : (1) Is my calculation of Inductance is correct for required deign of inductor...

06 July 2018 9,747 0 View

Matlab Simulink model of Average Current mode Control of Boost converter ?

Hi everyone can anyone help me designing average current mode control of boost converter. I have design the circuit in MATLAB simulink but Output voltage is not coming the exact value . Please...

04 May 2018 2,403 5 View

What is the most Operating System (OS) which can be INSTALL on Tiny hard devices like Raspberry Pi (RPi) hardware ?

I'm targeting to deploy a mesh network and manually configure MANET routing protocols. I'm preparing scenarios, architectures, and hard devices needed to do that. Are there some step-by-step...

03 March 2021 1,931 5 View

What are anisotropic electrical and optical properties of a semiconductor due to?

In some materials, properties such as band gap, thermal conductivity differ along different crystallographic axes. What are the basics?

01 March 2021 1,923 3 View

How the Ground Plane implantation is performed without damaging (and w/o varying the undoped nature) the top Si (8-10 nm) in FDSOI technology ?

It is a general practice to introduce Ground Plane in FDSOI devices under the BoX. The Ground Planes are introduced by Ion Implantation through Top Si layer and Buried Oxide. I wanted to know that...

24 February 2021 5,974 4 View

Can a semi-conductor material have different absorption coefficient?

Does the absorption coefficient of the semiconductor changes with the change in the structure of the semiconductor? If you have a thin film and nanowire of the same semiconductor, will the...

23 February 2021 9,799 4 View

How can we determine the band gap of a composite material that is made up of a composition of direct and indirect band gap semiconductor materials?

I have a direct band gap material and an indirect band gap material. If I made a composite of both through physical mixing. Then how can I determine the band gap of such a material as the Tauc...

17 February 2021 8,104 4 View

Any resist stripper which can remove thick metal based polymer residue and which is compatible with doped silicon ?

I am looking some resist strippers which can easily remove metal based polymer residue after post dry etch process. I have some candidates below but not sure if they are compatible with doped...

21 January 2021 3,008 3 View

What is the best way to calculate electrical conductivity of semiconductors and the same system with a layer of oxide using Quantum Espresso?

I have tried BoltzTrap, and EPW but I'm not sure whether Boltzmann Transport Equation is a right approach for a complex system (semi cond. + an Oxide layer or even the semiconductor itself). Also...

11 January 2021 4,597 4 View

Is there a generalized method to derive current-mode model of any DC-DC converters?

Hi all, As new DC-DC converters are being proposed, associated control method should be proposed and based on the small-model signal analysis of the DC-DC converters. Using average space state...

06 January 2021 7,247 3 View

How to calculate the band potential of a semiconductor material using energy band gap?

I am looking for methods to calculate the band potential of ZnFe2O4 and Fe2O3.

05 January 2021 6,416 2 View

Application for Ph.D. in Inorganic Chemistry?

I hope to have the opportunity to continue toI hope to have the opportunity to continue to do more in-depth research, do more in-depth research. My main field is to use semiconductor metal oxides...

04 January 2021 1,148 2 View