What is the ignition (minimum required) temperature for the direct synthesis of Vanadium Carbide (VC) using Vanadium and Carbon (Graphite) elements?
Hi professor.
Check out the following:
Article Single step synthesis of nano vanadium carbide—V 8 C 7 phase
Article A new method of synthesizing ultrafine vanadium carbide by d...
Article Vanadium carbide and graphite promoted Pd electrocatalyst fo...
Article In situ synthesis of V8C7 nanopowders from a new precursor
Article Initial Stage of Free Pressureless Spark-Plasma Sintering of...
Article Fast synthesis of VC and V2C nanopowders by the mechanochemi...
Tungsten Carbide and Vanadium Carbide Nanopowders Synthesis in DC Plasma Reactor
The formation of Al4Si intermetallic phase was detected by XRD analysis due to the addition of Al as a sintering aid in an ultrahigh temperature ceramic composite. I want to know the melting...
09 October 2018 7,094 6 View
Is there any reference for the coefficients of thermal expansion of hexagonal single crystals? Especially, I need to know the probable differences between the coefficients at different directions...
02 March 2015 7,585 3 View
I have used the thermal etching method (vacuum atmosphere) for detection of grain boundaries. I would like to know which mechanisms or phenomena can lead to the appearance of grain boundaries? Do...
02 March 2015 8,052 7 View
Can the mismatch in the coefficients of thermal expansion at "a" and "c" directions of a hexagonal structure lead to the formation of stresses at the grain boundaries of poly-crystal ceramics...
02 March 2015 1,469 10 View
I need the exact nature of chemical bonding of ZrB2. I think it is mainly covalent, however, is there any reference or an exact database about he percentage of covalent or ionic bondings?
02 March 2015 4,612 12 View
What is the easiest way to check the stoichiometric variations during the sintering process of ultrahigh temperature ceramics such as ZrB2 or TiB2? How to recognize the final composition of the...
10 November 2014 7,894 0 View
Do you have any references about this topic? I am working on UHTCs (e.g. ZrB2-SiC composites)
08 September 2014 1,571 1 View
I have prepared some UHTCs through hot pressing at 1700, 1850 and 2000 °C. Open pores were dominant type of porosity in the samples hot pressed at 1700 °C, but the type changes completely to...
01 February 2014 4,474 5 View
Because of many porosities in the polished surface of a ceramic composite, I'm not able to detect the cracks induced by vickers indenter. Does the Direct Crack Measurement method only work for...
31 December 2013 2,128 3 View
What is the best and easiest method for thermally etching of UHTCs? I want to analyze the microstructure, calculate the grain size, and investigate the grain boundaries of a polished sample. Is...
11 December 2013 7,170 15 View
I am planning to collect human fecal samples for metatranscriptomic analysis using MGI. These samples are from indigenous people living in a region with high temperatures. I will have access to a...
06 August 2024 1,367 3 View
During low-temperature testing, new diffraction peaks that appear could be indicative of several phenomena. In one of our tests, we observed notable new peaks around 40° and 45° in a specific...
06 August 2024 726 3 View
I have been using paraffin, but the deposited ZnO still detach from electrode. What is the best binder to modify graphite paste electrode with ZnO nanoparticles?
03 August 2024 4,624 3 View
I imagine the battery drives the graphite into a carbocation, then chloride is oxidized to donate the electron to the carbocation, but what pushes the lost electrons of chloride to be shared...
03 August 2024 5,384 0 View
I am in search of a modified Hummer's method, which can be used to synthesis graphene oxide within 6-8 hours. As I am a student it is not allowed for us to work after 5 in the laboratory. So I am...
01 August 2024 8,368 2 View
A typical reforming section in a large-scale Haber-Bosch process (Figure 1) comprises two reactors. A mixture of methane (CH4) and steam (H2O) is fed into a primary reformer to produce syngas via...
01 August 2024 7,051 5 View
The starting material is a finely ground powder. Some particles contain more graphene than others.
30 July 2024 3,978 2 View
Greetings. I’m currently running a nested pcr for giardia. My mastermix comprised of 3mM Mgcl2, 5unit of taq polymerase, 0.2uM of forward and reverse primers each respectively and 0.2mM of dNtp...
22 July 2024 9,761 5 View
Thanks
22 July 2024 1,143 3 View
Suggest the best and shortest route for the chemical synthesis and and green synthesis of magnetite(Fe3O4) The chemical synthesis should contain the least dangerous chemicals along with full...
21 July 2024 2,476 2 View