07 February 2018 3 6K Report

Hi everyone,

I have a huge database of results for thousands of simulations that I have run in Abaqus.

I want to write a lookup table in Python which will make it wasier for the user to plug in parameters and get the corresponding results.

I have a fair knowledge of python.

Could someone please link/refer some material or examples where-in lookup tables have been created using python? I would really appreciate any kind of help.

More Paritosh Hebbal's questions See All
What is the difference between Min (in-plane) Principal Stress and Min Principal stress in SHELL elements Abaqus?

Hello everyone, In Abaqus, my model uses shell elements. After the simulation when I try to compare the principal stresses, there are 4 possibilities : 1. Max In-plane Principal 2. Max...

13 September 2018 3,698 3 View

When to use Hyperelastic material in Abaqus?

Hello everyone, In my model (predominantly rubber), I get a maximum strain of around 15% compared to the initial state. I have experimental data for the rubber compound I am using, and I want to...

13 August 2018 565 3 View

Abaqus : How to view beam section forces in tangential (beam) direction?

Hello everyone, I would like to know how to view the beam section forces in the axial direction of the beam. I have selected SF in the output field variables, and am not sure if SF1 means axial...

29 July 2018 7,200 3 View

What material model is usually preferred for rubber in Abaqus?

Between and Elastic-Isotropic model with a low young's modulus, and a Hyperelastic Material that fits best with experimental data, what model (overall) gives relatively good results with less...

01 June 2018 6,494 3 View

How to define the anisotropic behaviour of a SOLID material in Abaqus?

Hello Everyone, I have the effective properties of a material (E1, E2.. v12, etc) as a function of the strain (epsilon11, epsilon22, epsilon12) as shown in the figure. I want to apply these...

30 May 2018 6,188 2 View

How do I model contact between beam elements?

Hello, I am modeling a yarn-knitted reinforced rubber hose in Abaqus, in order to measure the expansion and burst pressure. As seen in my model, I have used BEAM section for the aramid cords,...

24 May 2018 4,311 1 View

Can the RVE be homogenized in a NLGEOM step in Abaqus?

Hey guys, I have a RVE (representative volume element) where the matrix is rubber (highly nonlinear). I want to run my analysis with the NLGEOM option ON. What I want to understand is, after...

12 May 2018 5,811 2 View

What is the advantage of beam elements vs solid elements in this particular application?

Hello everyone, I plan to model a knitted reinforcement within a rubber hose in Abaqus in order to analyse the various stresses sustained by them during hose expansion. I am wondering whether to...

08 May 2018 227 8 View

Can I create this kind of a gui in python?

Hello everyone, I plan to create a GUI in python (or any suggested tool) which essentially reads a huge collection of data from a CSV table, so that when the user selects a certain combination of...

05 May 2018 5,515 2 View

How do I mesh this model so that the opposite faces have matching nodes?

I have imported this model from a CAD program. I am having difficulty meshing it. I would really love any suggestions as to how I can go about achieving the following : 1. The model is symmetric...

15 April 2018 7,766 3 View

Similar questions and discussions
Dear all, I was wondering if anyone knows whether MGLtools and Autodock can run on Mac OS?

I have tried to download the 64-bit version of MGLtools however, as many times as I have downloaded and uninstall the programs, an error arises that the app needs to be updated. Thank you.

03 March 2021 5,997 2 View

I got 02 moderator values defining Johnson-Neyman significance regions. Is it an error?

Hi everyone, I am conducting research for my Master's thesis. I am using PROCESS by Johnson-Neyman to analyze my Moderator model. I test the relationship between Public Service Motivation and...

03 March 2021 2,350 2 View

Do I need to do linear regression before running mediation analysis using PROCESS MACRO by Hayes ?

I just wanted to check if I need to run a linear regression separately if I am using PROCESS MACRO to run mediation analysis. Thank you.

02 March 2021 4,359 3 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

Do I need to strip the PVDF membrane before staining it with colloidal gold?

Dear Colleagues, After running Western blot on PVDF membrane and detection using ECL, I would like to stain my PVDF with colloidal gold to be able to allign the ECL image with total proteins on...

02 March 2021 7,829 3 View

PACYC PCR not working after several attempts. Would anyone have any suggestions?

So, I have been trying to run a pACYC PCR which will be used later on for a Gibson Assembly. However the PCR is not working. I have already tried gradient PCR and changing extension time; however...

02 March 2021 1,146 2 View

What SPSS analysis should I run with one IV (with two levels) and two DVs?

Hi, I am trying to figure out which test would be most appropriate to run for the following question: Is there a difference in task blood pressure between smokers and non-smokers? There are two...

01 March 2021 8,235 2 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

OpenBCI eeg--has anyone used them?

I'm looking to try out an off-the-shelf EEG set for some exploratory work. Curious if anyone has used the OpenBCI, and how much set-up work is required. I've heard they are more difficult to get...

01 March 2021 4,128 3 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close