LiFePO4 is used as a cathode in lithium-ion batteries, but its poor conductivity is its main drawback. Can carbon coating improve its conductivity?

More Nesrine Dhouibi's questions See All

How can we explain the viscosity Arrhenius behavior of liquids?

1*/ Viscosity of numerous of liquids or it's mixtures obey to the Arrhenius behavior. it means that the corresponding activation energy (Ea) is constant. How can we explain this constance? 2*/ In...

07 August 2014 2,824 3 View

How to size battery banks?

I am designing a small grid connected solar PV power-plant. As the battery's capacity is specified in Ah and demand in kWh. What is the best way to size the battery bank? I have battery price in...

28 February 2021 1,638 3 View

How to model the battery pack in PSIM or PSCAD?

Hello, I have simulated a single battery cell using Thevenin equivalent circuit. For a battery pack, I have a large number of cells connected in series and parallel connections. Is there any way...

28 February 2021 2,116 1 View

How to calculate battery consumption for IoT device?

Hi, everyone I'm working on a privacy-preserving algorithm that will apply to IoT devices. So, I need to measure the power consumption by implementing this algorithm. Any suggestion, advice,...

25 February 2021 8,749 6 View

How the Ground Plane implantation is performed without damaging (and w/o varying the undoped nature) the top Si (8-10 nm) in FDSOI technology ?

It is a general practice to introduce Ground Plane in FDSOI devices under the BoX. The Ground Planes are introduced by Ion Implantation through Top Si layer and Buried Oxide. I wanted to know that...

24 February 2021 5,974 4 View

How to delaminate copper in water-based anodes?

Hello everyone, I'm looking for a way to delaminate copper current collector of water-based anodes in Li-ion batteries without damaging the graphite film. I tried different materials such as HNO3...

24 February 2021 3,785 3 View

How to dissolve cross-linked Amberlite IRC120 H, hydrogen form resin?

Hello all, I have used Amberlite IRC120 H, hydrogen form acidic cation-exchange resin for the ion-exchange of waterglass [sodium silicate solution -- 40% Sodium silicate (mol ratio > 3.2)...

21 February 2021 5,614 3 View

What is the difference between AC conductivity and DC conductivity? Is AC conductivity = ionic and DC conductivity = electronic?

I am reading papers on batteries and although mostly people have reported ionic conductivity in Scm-1 but some have reported DC conductivity as well I and am confused as to what that is. Any help...

21 February 2021 9,207 6 View

How to prepare electrolyte of NaClO4 salt for Na-ion battery? Any problem with this salt?

Hello, I am trying to make anode for Na-ion batteries. I have no experience with preparation of the electrolyte for any batteries. NaClO4 salt are available and I am planning to use EC:PC as...

21 February 2021 8,132 1 View

Where can the fault diagnosis data set of lithium battery be found?

Most of the data sets on the network only contain good information about the voltage and internal resistance of lithium batteries. The data of faulty battery is missing. Who can help me, I will be...

21 February 2021 8,659 1 View

Not able to charge-discharge Li-ion coin cell at higher C rate ?

I am working on cathode material. I have made different Li-ion coin cell against Li metal using commercial available cathode materials such as LCO,LMO, LFP and NMC and also with the lab...

18 February 2021 1,450 3 View

Ozan Toprakçı

upto certain limit carbon coating will improve conductivity, but if you add a lot of carbon in the precursor you can get different types of impurities. After that point you may increase conductivity but it will contaminate structure and capacity values will decrease.

Nesrine Dhouibi

Thank You for you all

Ahmad Azmin Mohamad

try to find keywords "pre-heating LiFePO4" in google scholar, you will find lot papers preparing 'carbon coating from decomposition of gelling agent"