I am looking for the release parameters of Microtrol beads for Adderall XR so that I may include absorption rate or rate constants in a pharmacokinetic model of Adderall XR. Can you describe the kinetics or provide references?
Yes. This will be helpful for not only there is some useful content but the names may be useful if I can establish the contacts. Thank you Fakhrul.
Hi everyone, I'm a researcher working with proteins and I have a question about performing GPC (size exclusion chromatography). Lysozyme is known to hydrolyze peptidoglycan, which is a component...
25 May 2024 5,979 3 View
I perform al alkylation reaction on an imdazole compound where the alkyl reagent (1-Iodo-Octane) was in excess. After the reaction was completed, I then performed an extraction, followed by...
24 May 2024 8,042 2 View
Hello, I'm exploring whether incorporating edge weights in a network affects the extent to which the network is partitioned into clusters of closely connected nodes. Specifically, I'm...
13 May 2024 5,078 0 View
I was told by a lab colleague that 'after purifying a protein with a his-tag using imidazole, it is crucial to quickly remove the imidazole. Keeping the protein in more than 200mM of imidazole is...
04 March 2024 4,893 1 View
Hi all, Do you do DO calibration while the production is ongoing? Typically I don't do it. However, my recent data showed that offline pO2 is extremely high (approximately 300mmHg) but the...
22 December 2023 3,270 0 View
I want help on design the draw profile daily on domestic water (throughout the day) using TRNSYS. Please your help !!!
29 November 2023 1,165 0 View
I'm working on preparation of protein lysates from E.coli I read in a few paper that magnesium acetate should be added before sonication what is role of the Mg ace in cell lysis?
03 November 2023 4,891 2 View
I'm working on isolating recombinant protein in E.coli (Ni-NTA) I'am trying to purify recombinant protein that I overexpressed E.coli BL21(DE3)pLysS using the pCold1 vector. The proteins have...
03 November 2023 3,066 3 View
I do not doubt climate change and the disasters that come and will come from it (Some thoughts on climate change, resource constraints, and adaptation ). However, one thing puzzles me: why would...
28 October 2023 4,607 8 View
I am making an experiment about privacy and view-out in Virtual Reality (VR). The experiment has a lot of combinations of scenarios. I have 2 seasons, 4 locations, 3 positions and 3 window-sizes...
15 September 2023 7,046 3 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
Request Python code from this article : Gender equity of authorship in pulmonary medicine over the past decade. THANKS!
08 August 2024 6,242 2 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
Visual Studio Code (VS Code) has become a popular choice among developers for several reasons: 1. **Free and Open Source**: VS Code is free to use and open source, making it accessible to...
07 August 2024 7,013 4 View
Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...
06 August 2024 9,986 2 View
I received an e-mail invitation to join the editorial board of Clinical Cardiology Updates. While I have published a few articles related to cardiovascular disease, there are lots of colleagues...
06 August 2024 8,981 8 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View