I want to weld two tubular members in Abaqus(see figure). How can I do it. I am using the cut merge option. Will this option be considered welding? If not, then what do I need to do? Can you please guide me? Thanks
It better to model it in any modeling software like solidworks, or Catia
mesh it in Hypermesh and use Abaqus as just processor
Easily you can find many elements in hypermesh to mesh for welding
Thank you sir
Yes, merging can be considered as welding. Another interaction is "Tie" that you can use it for.
I am working in fungal fermentation of soybean meal and there is bacterial growth in them at times. I am trying to quantify fungal cell counts and bacterial cells; but I haven't been able to do at...
07 August 2024 7,535 4 View
The threshold voltage (Vth) of a MOS device plays a crucial role for its operation. At the same time, noise is an intrinsic factor. So how noise (flicker or thermal) change with the change in...
29 July 2024 3,246 0 View
It is being seen that Editors of some reputed Journals are putting on hold the manuscripts and not updating review states even passing more than six months from submission. Researchers are...
24 July 2024 8,596 2 View
Hello, I am a master's student currently conducting lentivirus transduction experiments in Jurkat cells. The virus is not effectively entering the Jurkat cells, so I am planning to use an...
21 July 2024 4,676 4 View
If you don't understand my question let me know
21 July 2024 563 1 View
I am working on scale development in behavioral finance by undertaking a mixed-method approach using the exploratory sequential design. The phenomenon has diverse meanings in existing literature...
20 July 2024 9,153 11 View
I need to convert Available phosphorus into total phosphorus
18 July 2024 6,799 3 View
Bioinformatics tools like peptide cutter
15 July 2024 6,453 1 View
The burden of obesity is enormous. The greater challenge lies in accurately diagnosing obesity at the right time, reflecting the true increase in visceral fat. BMI may not accurately represent...
14 July 2024 8,771 4 View
How does high humidity affect the growth and development of crops?
10 July 2024 7,258 20 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...
08 August 2024 4,831 4 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...
06 August 2024 9,986 2 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...
05 August 2024 3,665 0 View