Is there any publication about Zirconia Toughened Alumina reinforced in Co-cr-mo Alloy?

More Raies Ahmed Khan's questions See All

ZTA pre alloyed powder?

Where can i find ZIrconia toughened Alumina pre alloyed powder.

01 February 2015 2,315 2 View

Where can I find Co-Cr-Mo (ASTM F75 ) alloy?

can anyone give me the email id or the address of the suppliers of Co-Cr-Mo (ASTM F75 ) alloy. I will be very thankful.

11 December 2014 8,046 5 View

What is the contribution of the ZTA if mixed with the cobalt chrome alloy?

What will be the effect of the ZTA if mixed with the cobalt chrome alloy in small amounts. Haven't found any journal containing the same. Can anyone help with that? Regards

05 June 2014 2,642 2 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

How do I conformally do PR spin coating on trench structure?

I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...

08 August 2024 2,298 0 View

Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,563 0 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

Why doesn't chromium 2+ ion use all its d-orbitals to receive lone pairs from six waters in [Cr(H20)6)]3+?

I'm guessing it's because the ligand experiences too much electron repulsion or proton repulsion from the chromium to insert them close to the 3d-orbitals which are close to the metal nucleus. Is...

03 August 2024 1,370 1 View

How select composition for ods-high entropy alloys?

31 July 2024 2,795 1 View

What should be the sample container for the hydrothermal reaction in a microwave reactor at 180 °C for 10 min at the heating rate of 5 °C per minute?

Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container

30 July 2024 7,326 1 View

Which statistical test should we use?

N=6 Comparing pre and post test likert scale responses. Participants are mix of practicing & preservice teachers.

30 July 2024 7,233 4 View

What is the reason I get 400nm nanoparticles using an extruder with 200 nm membrane for cell membrane coating?

I am trying to coat my micelles and PLGA based nanoparticles with cell membrane using an Avanti mini extruder according to literature . I use 200nm membrane but my particles end up to be 400nm And...

30 July 2024 3,294 3 View

Veeravenkata Veera VARA PrasadVeeraVenkataveera Prasad Varaprasad KK

As per as my 12 yrs experience knowledge there should not be any publication but dear friend you better search in rsjournals,sci journals, bentham thomas,springer and science direct journals and elswier publisher journals.

If it is not there then blindly you go head to your research work.

Raies Ahmed Khan

thankz venkata...