Is there any particular example of tangent hyper fluid and what are the physical significance of the parameters involved in the stress tensor?

More Zakir Ullah's questions See All

Can anyone suggest me the best way for Regression analysis of Accidents?

Dear Altruist, I want to make a regression analysis based on accident data. But I am not finding the necessary information about what type of regression is more applicable for analysis accident...

23 February 2021 9,956 3 View

Why the difference between degrees of nonclassicality of the input states is required for nonzero entanglement in the output state of a beam splitter?

By considering two single-mode Gaussian states at the input of a beam splitter, it is seen that the entanglement of the output two-mode Gaussian state depends on the difference between the degrees...

22 January 2021 3,490 3 View

Hi Everyone. I want to conduct DEMATEL analysis for my survey. Everything is in line except the MAXIMUM MEAN DE-ENTROPY (MMDE) ALGORITHM. Need help ?

I can't find any manual or procedure on how to conduct the MMDE process. It looks like most of the literature has copy-pasted the stuff without any method of how to do to it. Any practical book,...

07 January 2021 1,804 2 View

Is there any specific software available for graphical presentation of signaling pathways/cycle in cells?

I'm planning to write a Review article, to make it more worthy and easy to understand for the targeted audience, I'm thinking to add some signalling pathways, and unfortunately, I have no idea how...

30 December 2020 6,395 2 View

Does anyone have experience in infecting suspension cells (like THP-1 or K562 etc) by retrovirus?

I am trying to make stably expressing cell line of my gene of interest in Suspension cell line using retrovirus but i don't have recommended protocol. I have searched literature but mostly they...

14 December 2020 8,274 3 View

Hello I have a question about solar cells (perovskite solar cells) modeling in COMSOL?

I have done all optical simulations in RF module, now how can i find generation rate of electrons and holes, secondly how can i use these generation rate in semiconductor module to find further...

11 December 2020 6,652 3 View

Can a mathematical model be added to a paper on bean genetic and diseases manuscript?

10 December 2020 2,300 14 View

Can anyone help me to find research paper of "Banks, W. H. H"?

Dear researchers, I need this research paper "Similarity solutions of the boundary-layer equations for a stretching wall by Banks, W. H. H (Bristol, University, Bristol, England)." If anyone...

07 December 2020 2,157 1 View

Straight chain or Ring peptide for inhibiting a homo-dimer of a 20 KDa secretory protein?

I am designing a small peptide to inhibit a homo-dimer of a small secretory protein (about 20 KDa). I need suggestions on, which option would be better? a straight-chain peptide or a ring-shaped...

03 December 2020 4,145 5 View

How can I simulate noise of CMOS Image Sensor by sentaurus TCAD?

Can anyone tell me how to simulate noise of CMOS image sensors, such as thermal noise and flicker noise with sentaurus TCAD?

09 November 2020 9,616 4 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

Can we distinguish the type of free fluid inside the pelvic and abdominal cavities whether blood or serous fluid using the ultrasound?

during ultrasound examination of acute abdomen, sometimes we see free fluid , can we know the type of fluid ,whether blood or not , using ultrasound only? if yes , what are the sonographic...

01 March 2021 7,476 4 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

Is there a deep reason for using the squared modulus of the wave function as the probability density of the existence of the particle?

I think we were all surprised at the first time we got to know quantum mechanics that the squared modulus of the wave function is the probability density of the existence of the particle? The role...

28 February 2021 6,282 9 View

How relevant is Mini slump cone?

for all the rheology researchers, my question is, how relevant is a mini slump cone (smaller than a standard 50 cent rheometer). currently based on testing, the thickness of slumped material is...

26 February 2021 3,668 1 View

Ijaz Durrani

Hello Dr Zakir Ullah: Here is my input concerning your question:

Whipped cream, blood, solutions, melts, paint, polymers, and ketchup are the main examples of the tangent hyperbolic model in the fields of industry and biology. probed heat transfer in dusty hyperbolic tangent fluid with respect to magnetic field and thermal radiation toward a deformable sheet.

Article Inclined hydromagnetic impact on tangent hyperbolic fluid fl...

Article On Purely Mechanical Simple Kinematic Internal Constraints

I hope the above helps in facilitating you in your research. Best regards--