Is there any other way to find Heat Transfer Coefficient in COMSOL Multiphysics?

10 October 2018 0 9K Report

Hi every one,

Is there any other way to calculate Heat Transfer Coefficient in the COMSOL Multiphysics? I use the expression below but I don't get much good results as expected.

h=q/(T(R,z)-Tb(z))

Where, Tb(z)=T0+(2*q*z)/(R*V0*Rho*Cp)

any help is well appreciated,

Thanks

Badges
Science topic

More Siamak Vajdi's questions See All

COMSOL, How can I get the correct answer?

Hello, I want to solve the simplest form of my project (Attached) but the velocity in the length of channel in not constant, and the temperature at outlet comes 36Celsius degrees (309K) but it...

31 December 2017 1,085 5 View

COMSOL, how is it possible to enter an expression as a variable in PDE?

Hello, How is it possible to enter an expression as a variable in PDE? I am using Coefficient form PDE and I have my PDE equation attached. I have Material properties dependent on Cv and T defined...

10 November 2017 9,910 5 View

COMSOL Multiphysics, Particle Tracking Module !?

Hello everyone, I am trying to simulate flow and heat transfer of a non-uniform nanofluid (Nanofluid properties changes with Phi (particle volume fraction)) in a microchannel. Is it possible in...

01 February 2017 4,532 2 View

COMSOL problem, Laminar flow + Heat transfer? why adding heat transfer affects laminar flow?

31 December 2016 3,813 12 View

COMSOL, Problem in solving laminar flow (finding entrance length)?

11 December 2016 7,158 17 View

How can I couple 2 temperatures in different physics in COMSOL!?

Hi How can I couple 2 temperatures in different physics!?I have laminar flow and heat transfer in fluids Modules and one extra PDE Eqn. I want to have the same Temperature in both PDE and Heat...

10 November 2016 3,491 4 View

COMSOL Multiphysics problem: How is it possible to couple 2 temperatures in different physics!?

How can I couple 2 temperatures in different physics!? I have laminar flow and heat transfer in fluids Modules and one extra PDE Eqn. I want to have the same Temperature in both PDE and Heat...

10 November 2016 2,040 6 View

Is there any tutorial for comsol general projections?

Hi, im trying to make a projection in a 3d comsol model. I have a non uniforme chanel and my intention is to get the average tempreture in the y-z cross section and se the average tempreture...

02 March 2021 4,624 4 View

Is it possible to do piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch?

How to do Piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch? Piezoelectric coupling between the rectangular substrate and rectangular...

02 March 2021 9,833 3 View

What are the countries most affected by extreme rainfall as a result of climate change?

Increased heat, drought and insect outbreaks, all associated to climate change, have increased wildfires. Decreasing water supplies, declined agricultural yields, health impacts in cities owing to...

01 March 2021 7,168 9 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Heat exchanger with liquid Nitrogen as coolant?

I want to cool Natural Gas from 195 Kelvin to 138 Klevin in a heat exchanger by using liquid nitrogen as the coolant medium. When entering the heat exchanger, the liquid nitrogen will have a...

01 March 2021 6,450 5 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

PUC19 as a transfer plasmid for lentiviral delivery?

Hello, Is it possible to use pUC19 as a transfer vector to be packed in using the second generation viral particles packaging system( pMD2.G; psPAX2 plasmids)? As far as I understand it there is...

28 February 2021 4,868 2 View

Exit velocity of natural gas from pressurized tank?

Hi Guys. I'm a mechanical engineer and have a bit trouble, would be very glad if you could help me with my questions. I have a pressurized tank which contains Natural Gas at 200 Bar and 293...

26 February 2021 6,253 3 View

How to use measure capacitance change in COMSOL time dependent study ?

I want to measure change of capacitance due to relative displacement between two parallel plates in COMSOL. Distance between two plates changes with time. So I'm using a time dependent study but...

26 February 2021 8,567 3 View

Anyone that can help with Maxquant TMT16plex which is missing?

Hi I am very new to proteomics analysis. I have got raw files from core facility running thermofisher TMT 16plex 4 hours. I cannot find on maxquant the option TMT16Plex there is only up to 11...

25 February 2021 1,675 3 View