Dear all, Is there any model available to predict the "possible diseases" based on the available pollutant concentration in air ?

In detailed human health risk assessment models. Is there any model that can predict the possible disease.

21 December 2020 7,535 5 View

How to get best LSTM model for regression problem? how to tune or select hyper parameters?

How to get best LSTM model for regression or prediction problem? how to tune or select hyper parameters?

29 June 2020 9,377 4 View

How to work with phasor model in matlab?

I am running IEEE 13 bus model in MATLAB with discrete time . But when I connect Renewable energy DFIG model with IEEE 13 bus system not working due to phase model of DFIG. How to rectify error?

31 January 2020 7,950 4 View

In fluent heat flux analysis results are not converging ?

I had solved the heat flux analysis of the multi-domain problem in fluent. Even after the 20000 iterations also the solution is not converging. As the iterations increase the results are diverging...

05 November 2019 1,713 3 View

Any specific procedure to be followed while converting one dimensional data into image?

Is there any specific procedure to convert 1D data to image before feeding convolutional neural networks ?

18 October 2019 8,309 4 View

Do addition of nanopartilces in soil increases the Plant yield ?

Can any one explain me that addition of nanoparticles enhances the growth of plant and produces more yield. If so, can anyone list me the nanoparticles i can use Plant is Tomato and Aubergines

24 June 2019 5,402 3 View

Do anyone have working protocol for cardiac perfusion in mice?

I am new to perfusion. I need to do cardiac perfusion in mice and my area of interest is brain further to sectioning and IHC. Does anyone have standard protocol of cardiac perfusion for this. Help...

29 May 2019 6,919 3 View

Is addition and removal of Co-author during submission of revised article is acceptable @Elsevier ?

I like to know the removal, addition and shuffling of co-authors is against moral and ethics in Elsevier Journals. Is it necessary to contact a editor to make such changes

20 February 2019 3,676 18 View

How to gelatin coat flasks for primary rat astrocyte culture?? Suggest me with how much percentage gelatin should i use??

I'm gonna culture rat mixed glial cells for first time. suggest me with how much percentage gelatin should i use to culture cells..

07 November 2018 7,023 6 View

How to design a model using moving meshing concept ?

I need to design a simulation, where model is stationary and the mesh is moving. Please share any tutorials and ideas Thank you

19 April 2018 7,550 2 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

How to eliminate Steady state error from Reinforcement learning genetic algorithm code?

The following code (see 1st 2 images attached) is used to produce PID controller values that are designed to control the system (G). The code finds the PID controller values (noted as k) by using...

28 February 2021 6,560 14 View

How to prevent ANFIS Model from negative prediction values in MATLAB?

I have input and output data set for "ANFIS modeling in MATLAB", and I am getting some negative predicted values of output in testing. However, the predicted values of output in training are...

28 February 2021 3,459 3 View