How to relate results of Welch 2 sample t-test vs two one-sided test for equivalence TOST?

Please, I have the next doubt: I have two samples (two different treatments) , and I want to prove that there is no difference in the average outcome. I test the data using the two one-sided test...

04 May 2018 7,611 2 View

How much time does the reviewing process for a paper submitted to the Journal of the Association for Information Systems take?

I know the acceptance rate is low, but we think we have 40% odds to get accepted. But my student would need the (conditional) acceptance or rejection notice no later than 8 months from now, just...

04 May 2017 2,333 1 View

Does any of these journals accept review papers?

There is no indication in the homepage of these journals, and I do not want to spend time formatting my review paper only to be dismissed because its nature (it already happened to me a couple...

09 October 2014 9,701 2 View

Source code for parallel Gaussian Elimination with partial pivot (2D cyclic blocks) ?

09 October 2014 3,105 0 View

How does one get the wind load or the drag coefficient of an antenna using OpenFOAM or ANSYS?

07 August 2014 1,500 8 View

Logistical regression using SPSS for a dichotomous dependent variable, with an independent variable of 1, 2, 5 and 10 seconds?

I have an experiment with 28 participants The independent variable is the times 1, 2, 5, and 10 used as the cross hairs during a task These 4 times were tested using 4 different blocks, each...

03 March 2021 9,692 2 View

Do I need to do linear regression before running mediation analysis using PROCESS MACRO by Hayes ?

I just wanted to check if I need to run a linear regression separately if I am using PROCESS MACRO to run mediation analysis. Thank you.

02 March 2021 4,359 3 View

How to normalise data on OPM package from R Studio ?

Good afternoon, I recently used OmniLog from BIOLOG for my experimentations : I tested the metabolism of different strains on 2 types of plates. I have 16 strains of 3 different groups...

02 March 2021 3,584 1 View

Which is suitable for use with Python? MySQL or SQL Server?

Which is suitable for use with Python? MySQL or SQL Server? What is your suggestion?

01 March 2021 3,422 3 View

How to choose ANN number of hidden layers and nodes?

Hello, Could you please share any interesting research explaining how to choose the number of hidden layers and nodes per layer in case of regression problems using ANN? Thank you, any help would...

01 March 2021 6,200 3 View

How to eliminate Steady state error from Reinforcement learning genetic algorithm code?

The following code (see 1st 2 images attached) is used to produce PID controller values that are designed to control the system (G). The code finds the PID controller values (noted as k) by using...

28 February 2021 6,560 14 View

Can anyone provide the Support vector regression code structure of LIBSVM MATLAB or python ?

Please, if Gaussian Parameter optimization is possible in this code structure

28 February 2021 278 3 View

How could I take into consideration the weights of observation in a system of seemingly unrelated regressions (SUR) in rstudio?

I build a model of 4 regression equations (probit and OLS) in R studio. I need to take the weights of observations into consideration. While it is simple to do so for every regression equation,...

27 February 2021 1,233 1 View

VIF very high, but correlation is low and coefficient is significant. Which one whould I choose?

Hello. I have a question whether if my coefficients (statistically significant) would be valid when VIFs are really high. In my model, there are independent variables(IV), moderating variables...

26 February 2021 956 13 View

How to plot the probability paper of Gumbel distribution using R programing?

In R-studio, there are many commands of Gumbel package. Arguments are also different. I`m asking about the alpha parameter of the Copula which must be greater than 1. If this is the one used to...

25 February 2021 5,229 3 View