12 October 2017 3 6K Report

Permittivity of liquids confined within some boundary have been measured by many researchers. Lets assume that liquid flows through some channel with some flow rate. Will permittivity of liquid change? If yes, how can we relate this change with flow rate and other parameters? And if no, why fluid dynamics did not change energy interaction property of liquid?

More Tahir Ejaz's questions See All
How to figure out easily the right journal with the right scope for your paper?

According to my experience most of the selected journals during paper submission are based on journal text matching suggested results from Springer, Elsevier,,,Etc. then the manuscript happened to...

01 March 2021 1,786 3 View

How to model the battery pack in PSIM or PSCAD?

Hello, I have simulated a single battery cell using Thevenin equivalent circuit. For a battery pack, I have a large number of cells connected in series and parallel connections. Is there any way...

28 February 2021 2,116 1 View

Is there any software or formula for sample size determination by using sensitivity and specificity?

I want to conduct research on the diagnostic performance of some tests. I want to calculate sample size by using the sensitivity and specificity of the test in the previous studies. So Is there...

23 February 2021 619 5 View

What is the best way to track bird migration?

Migratory birds are globally scattered. What should be the ways to track them? Except ARGOS. Elaborate.

25 January 2021 2,355 4 View

How i can reduce the number of atoms using Vesta ?

I'm a new Vesta learner, I have downloaded cif of Ch3Nh3PbI3. Total number of atom in chemical formula for Ch3Nh3PbI3 is 12. But when i convert this cif to poscar file using Vesta, total number of...

14 January 2021 5,733 11 View

How to determine the sample size for ANOVA in GPower?

Hi, I am going to execute an experiment with the four categorical variables (A=2 levels, B=2 levels, C=2 levels, D= 5 levels) and one dependent continuous variable. There are total of 40 groups...

19 December 2020 3,600 4 View

How to detect the objects with same color using HSV opencv-python?

I am trying to detect the objects in real time using HSV method with python. I have several objects with colors and shape but how to detect the particular object with same color objects. For...

10 December 2020 3,614 4 View

How to calculate the replacement cost of battery?

As battery needs to be replaced after the specific charge and discharge cycles mentioned in the datasheet. If we have the time series data of battery power and energy capacity, then how can we...

01 December 2020 3,433 3 View

Can anyone please elaborate the relationship between charge and discharge cycles and battery lifetime?

I am designing the optimal HESS capacity for the renewable system. I have to select the cutoff frequency of low pass filter to divide the low and high-frequency components. charge and discharge...

05 November 2020 8,397 3 View

How to select the frequency range in MATLAB Wavelet toolbox?

I have a continuous, time-domain noisy signal and want to decompose into low-frequency (LF) and high-frequency(HF) components using Wavelet Toolbox. But, I am unable to select the frequency range....

29 October 2020 5,219 5 View

Similar questions and discussions
MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

Does anyone know HRM channel in a 2 plex QIAGEN Rotor- Gene Q qPCR can be used as a separate channel?

I am going to have 3 different probes in my qPCR work that I am going to do. But I realized that the machine we have in the lab is a Rotor-Gene Q 2plex HRM Platform, saying it has green, yellow,...

01 March 2021 8,544 1 View

Can we distinguish the type of free fluid inside the pelvic and abdominal cavities whether blood or serous fluid using the ultrasound?

during ultrasound examination of acute abdomen, sometimes we see free fluid , can we know the type of fluid ,whether blood or not , using ultrasound only? if yes , what are the sonographic...

01 March 2021 7,476 4 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close