Is there any company provide a sharing user License in Ansys OR Abaqus,
I mean, I don't have enough budget to buy a commercial license to start working on my Start-Up, So I am looking for companies can provide me a sharing license to save money?
Hi Dr Mutafi did you find? Its been 3 years already. 😄
Hi Dr Wayo
I did not find. Im still thinking on this but not planning to not take a step this time. Dennis Wayo
Thanks for your feedback. I recently got a company who is willing to share Ansys 2020 R2.
Hi I am running a simulation in Abaqus for a concrete beam. Its fine aggregate replaced with sea-sand. I was wondering if I could find studies that measured the ultimate strain of concrete made...
22 February 2021 6,409 2 View
how can i collect many blood sample from the rat for pharmacokinetic study without killing the rat??
28 October 2020 2,675 8 View
The prediction plays the important role in detecting efficient protection and therapy of cancer. The prediction of mutations in gene needs a diagnostic and classification, which is based on the...
13 August 2020 4,590 4 View
find the correct answer
05 August 2020 4,474 3 View
Dear sir, to run the asymmetric causality (see Hatemi-J, 2012) or the hidden co-integration what is is the best way to get positive and negative cumulative components and is there any conditions...
13 February 2020 3,151 1 View
modeling mass transfer in surface evaporation using UDF in fluent 17.2 UDF and phase contour in attachment I will be grateful helping me enhancing my UDF
20 July 2019 3,441 2 View
I need books or videos or anything can help me to deal with Gauss aptech program
01 January 2019 8,782 2 View
I want to know How I can map the stress when preformed buckling and post-buckling. I read in one thesis, author mentioned about SIGINI/HARDIN subroutines. Unfortunately he did not explain about it...
27 July 2018 6,849 3 View
Hello all, I am working on a project where it includes a network of IoT connected to a server (Raspberry Pi 3+) . the raspberry pi has wireshark installed to analyze network traffic and save the...
19 June 2018 1,083 2 View
Raphanus raphanistrum resistance gene?
11 May 2018 5,944 2 View
Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,
02 March 2021 0 0 View
Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...
02 March 2021 4,910 3 View
The Lanthanide contraction which is the decrease in ionic radii of the elements in the lanthanide series from atomic number 57, lanthanum, to 71, lutetium, is due to poor shielding of the 4f...
01 March 2021 2,272 4 View
I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...
01 March 2021 10,078 1 View
Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...
01 March 2021 9,911 3 View
I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...
01 March 2021 6,661 3 View
I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...
01 March 2021 8,668 3 View
I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...
01 March 2021 736 3 View
I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...
01 March 2021 8,415 1 View
Hello, I am writing a python script to generate my model and write the input file. The problem is I have 1000 elements in my mesh and I want to assign different material properties to each...
01 March 2021 9,511 3 View