What is the best antimicrobial agent among metal oxides?

I am looking for an antimicrobial metal oxide agent for a polymeric implant and I am wondering which one is the best?

21 January 2021 7,068 5 View

Detection of insect eggs in stored and processed products?

Currently, in order to identify insect eggs in stored or processed products (such as contaminated flour or wafer samples), staining was performed based on the method mentioned in the below...

15 January 2021 6,362 5 View

Hello.Can you help me to Introduce "Scientific and research centers in the field of floods"?

The purpose is to identify flood forecasting, control, warning,.. If you have a booklet, book, article, file, site address, etc., thank you for the introduction or its link. Thanks for your attention

30 December 2020 610 4 View

Hello. Do your friends have any suggestions on the "latest watershed management methods"?

If you have a source, new book, article or educational booklet, please introduce it. Thanks

29 December 2020 5,665 1 View

I need a protocol for extracting ochratoxin A from green coffee beans for analysis on hplc, as well as the protocol for carrying out the calibr ?

ochratoxine A ; HPLC ; green coffee

29 December 2020 4,028 3 View

What is the most recommended multispectral-UAV to be used for delineating the shoreline?

Hi there, I am looking to purchase an UAV with an attached multi-spectral camera to use its images in delineate the shoreline. I need to take a vertical geo-referenced image (if possible) and...

21 November 2020 1,283 3 View

Why pathlines keep changing their patterns?

Hello, I am using ansys fluent to simulate a steady state phenomenon, even though the residual curves are absolutely flatten, pathlines keep changing their patterns over more iteration. I was...

12 November 2020 2,231 3 View

How to simulate fracture in the axle housing ?

Hey there, I want to simulate & analyze the fracture and fatigue (crack growth) in the rear axle housing of heavy tracks (Volvo company) in Abaqus. My question is which method is suitable for...

12 November 2020 3,377 3 View

How can i delaying a signal in Matlab script file without using simulink block (i want the instruction of delaying a signal in script file ) ?

How can i delaying a signal in Matlab script file without using simulink block? (i want the instruction of delaying a signal in script file )

27 October 2020 4,299 2 View

What would you do if MgSO4 did not fully dry your organic extract ?

Hi everyone, I used MgSO4 as a drying agent to suck all water droplets from my organic extract. However, even after adding MgSO4 three times and leaving it overnight, I still see some water...

14 September 2020 9,203 3 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Physics: Why do we describe light by referring to its wavelength, but microwaves and radar pulses by referring to their frequency?

In physics, the description of the properties of light generally refers to its wavelength (nm), while in the range of microwaves and radio waves we refer to the frequency of a signal (e.g. kHz or...

03 March 2021 1,682 3 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View