Hello all,
I have some MD trajectories and I have to calculare g(r) and other distribution functions.
Is there an easy way to compute them using VMD software? Maybe with a plug-in?
Thank you.
Hi Francesco,
If you use lammps you can calculate g(r) directly.
Also, if you have the trajectories you can have it using OVITO.
http://www.ovito.org/
Open the trajectorie
go to "Add modification" and then to "coordination analysis": there you have it.
best
A
I used GROMACS to generate the trajectories.
I was able to obtain some radial distribution functions with VMD, however these are the so-called h(r) (basically a counting of the contacts), while I would like to have true g(r).
use gromacs tools gmx_rdf:
http://manual.gromacs.org/programs/gmx-rdf.html
In case you are still wondering how to do it with VMD:
http://www.ks.uiuc.edu/Research/vmd/plugins/gofrgui/
how to extract g(r) using VMD
The use of interactive data visualization tools is becoming very popular to enable users explore the data from different points of view. These tools allow users to investigate data from different...
16 September 2020 7,744 10 View
I am trying to determine which fuel cell performs better than the other. I have the polarisation and power density curves for each of the fuel cells but I am not sure what is the best way to...
04 May 2020 4,688 1 View
I'm using antennaDesign tool box of Matlab to design a insetfed Microstrip antenna. Now I want to compare the results with the same antenna, but with a PBG substrate. How can I do this?
10 April 2020 7,257 4 View
Hi! I will try to measure intracellular lactate through lysing the cells in 20 mM Tris-HCl, 150 mM NaCl and 1% NP40. I'm going to use a clinical kit, which is constituted of Pipes buffer, pH 6.8....
30 January 2020 5,211 2 View
I wanted to download AlexNet and VGG-16 CNN models that have been pre-trained on medial images. It could be pre-trained for any particular mdeical image related task like segmentation,...
09 December 2019 9,689 5 View
I have been working on cryosectioning adult zebrafish with large tumors in their abdominal region, but I am getting a significant degree of holes/tearing in the sections as they come off the...
18 August 2019 1,716 2 View
The study will be conducted to grade 10 students in the Philippines
17 July 2019 2,788 3 View
Since there are a lot of tools that researchers use in order to follow the expossure, citations, journalistic mentions, etc., and since everyday this programs like altmetrics or elsevier's...
03 April 2019 2,952 3 View
I would like to know if the lubricant properties of internal combustion engines are affected by the use of ethanol, aqueous ethanol solutions or ethanol-Diesel blends as fuel, especially for...
02 November 2018 4,889 2 View
I ran a TDDFT calculation of a copper(II) complex to get the UV-Vis spectrum. The maximum wavelength of each band is basically the same for both spectra (calculated and experimental), but some of...
19 April 2018 2,246 5 View
How to calculate the RMSD values for a MD simulation using MOE?
07 August 2021 0 0 View
When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.
16 June 2021 0 0 View
Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...
03 March 2021 5,978 5 View
Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...
02 March 2021 2,431 3 View
Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...
02 March 2021 4,910 3 View
Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...
02 March 2021 4,569 4 View