10 May 2021 4 6K Report

On what basis are the section size of the chevron brace and the SR (The ratio of the stiffness of the brace and the damper to the stiffness of the story) determined in design of the TADAS damper?

More Sahar Ebrahimi's questions See All
Is this a facetotecta nauplius?

This larva was captured using a plankton net in the Persian Gulf during the summer. I believe it may be a Facetotecta nauplius.

08 August 2024 3,746 4 View

Following click reaction in cell lysates, protein is immobile and remains at the top of the gel in SDS-PAGE?

I am using CuBr/THPTA for a click reaction in total cell lysates. I am facing issues with my protein sample in non-reducing SDS-PAGE where it's not migrating properly and most of it remains at the...

29 July 2024 950 4 View

Which filtration method to go for run off water from dirty solar panels to be used again?

We are working on a robot that cleans solar panels using fresh water supply and a rotating brush. We are trying to conserve as much water at possible by recycling the dirty water that is collected...

28 July 2024 5,778 2 View

When making abraxane with Nab tech, why is 9:1 Chloroform&EtOH used as solvents?

Is it the best optimization ratio based on experiments?

22 July 2024 8,170 0 View

Can diamond be grown using molecular beam epitaxy?

Can diamond be grown using molecular beam epitaxy?

22 July 2024 9,755 2 View

How can I use LabVIEW to control of an ethernet-based driver?

Hello everyone, I am new to LabVIEW, right now we need to control the movement of an ethernet-based stage drive. We got the sample code from a collaborator but their instrument is USB-based, so we...

11 July 2024 5,385 2 View

Systematic review meta-analysis paper?

Hi everybody, We are trying to write a systematic review meta-analysis paper. But I could find 19 references. I think 19 references are not enough to do a meta-analysis section and it is better to...

10 July 2024 5,490 5 View

Do the SHSY5Y cells tend to form multiple layers over each other when highly confluent?

I have attached pics of the SH-SY5Y cells within a seeded plate after reaching >80-90% confluence. Are these dark clumps of multiple growing cell layers? Or dead cells? Any clue? many thanks.

01 July 2024 8,361 3 View

Adding isopropanol directly to eluted RNA samples?

I have my RNA samples eluted in nuclease-free water. But now I want to store it for a longer period. Can I add isopropanol directly to my samples to store it without doing a second round of TriZol...

23 June 2024 2,576 4 View

HI, How to find phase response in CST?

I'm simulating a metamaterial unit cell. I want to plot Frequency Vs Phase Response. Also I want to extract permeability and permittivity. Kindly share the steps.

23 June 2024 3,446 1 View

Similar questions and discussions
Adding a frame element into an OpenSees model after running initial?

Hi, I am running an opensees model of a 2-bay 1-storey frame with settlement at the mid-support. I wanted to add an additional frame element as a bracing to the analyzed frame after it sustains...

08 June 2024 4,132 0 View

I am currently trying to do research on Buckling Restrained Bracing. Can anyone give me reference paper about the location of hinges for modal in SAP?

I am at the initial stage any suggestion or help will be highly appreciated.

04 May 2024 626 1 View

What is your recommended aligner wear protocol?

Different clinicians follow different aligner wear protocols for their patients such as, 7,10 or 14 day protocol. What are your views?

14 November 2023 9,729 4 View

How to model an EBF Shear Link in opensees?

Hi everyone, I want to model the shear links in an Eccentric Braced Frame Structural System. My problem is selecting the best element object in opensees/openseespy which can replicate the...

01 October 2023 7,368 5 View

How to model gap element in DIANA FEA 10.5?

I am currently working on my thesis in Retrofitting of soft story. At first step i am trying to validate a experimental test. There i need to model a bracing with gap in it. The bracing should...

04 April 2023 9,469 3 View

How to attain the cyclic hardening and softening in my model ?

Hello researchers, I have been modelling the cyclic behavior of bracings using ABAQUS. when I take the hysteresis loop once the model has run I get the graph with straight lines as shown in the...

22 January 2023 1,237 3 View

How can I calculate the effective stiffness in the multilinear plastic links in SAP2000?

I am modelling eccentric braced frame with shear link, and I model the Link as multilinear plastic Links, but I need to know how to calculate the effective stiffness and damping the link is...

21 December 2022 1,097 0 View

Can I use Plastic Hinges with Non-Linear Time history Modal Analysis (FNA)?

I am make a model of eccentric braced frame and I need to run it with FNA but no Plastic Hinges Results appear

06 November 2022 7,685 1 View

General member force-deformation relationship of braces?

How to calculate parameter ∆c which represents the axial deformation at the expected buckling load for braces as per ASCE 41.

02 November 2022 2,850 0 View

What statistical analysis should I use for a two group pretest-posttest design?

The "two groups" will be in fact the same group of people. The first time they will not wear a brace while the second time they will wear one. The posttest measure will be after a fatigue protocol...

11 April 2022 1,185 2 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close