11 November 2017 4 1K Report

How to study the heat transfer in a non homogenous structure by using thermal transfer matrix. because thre is no homogenus plans to make the product matrix.

More Sougrati Belattar's questions See All
Currently what is the maximum accuracy achieved by an infrared camera for temperature measurement?

the measurement of surface temperature by thermographic measurements has become a very important measure in several fields of industry but also in the field of research. From there it is important...

06 July 2019 8,069 4 View

In the context of studying the propagation of heat in the form of waves, what is the physical significance of the reflection coefficient?

The study of heat propagation can be done using wave formalism. In these conditions what is the physical significance of the reflection coefficient which obviously relates to the effusivities of...

08 September 2018 1,404 0 View

What are the advantages to study the heat tranmission in a wall in the frequency domain ?

In which case it is more interesting to study the propagation of heat in the frequancy domain?

05 June 2016 8,167 2 View

Between Ansys and Femlab softwares, whitch one is the more simple, flexible and the cheapest for thermal simulations?

We are looking for a software of thermal simulation and we want to compare Ansys and Femlab

05 June 2016 1,907 2 View

What is the best way to measure the surface temperature on a wall in civil engineering ?

is it to put directly the sensor on the wall or to make a groove in which the sensor in introduced by using silicon grease ?

04 May 2016 8,618 13 View

Similar questions and discussions
How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Is it true that $\det(V(A))$ may be only $\pm 1$, depending on $n$, for the last symmetric tridiagonal matrix $A$?

One can try to generalize the Vandermonde determinant in the following direction: Let $A$ be any symmetric $n$-order square matrix. Consider its powers' diagonal elements $(A^k)_{ii}$ and...

08 August 2024 6,690 1 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Why does my protein refolded to beta sheet during thermal denaturation analysis?

Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...

06 August 2024 1,989 3 View

How to heat polymer for about 130° without oil bath ?

is there any other way to heat a polymer evenly other than oil bath if so what are those and how to use it

06 August 2024 947 1 View

Usage of internal standards in LC-MS/MS analysis?

Have you ever seen a LC-MS/MS method uses both internal standards and external standards (in matrix matching purpose) but the concentrations of internal standards are outside the calibration curve...

05 August 2024 3,084 6 View

What should I do with parameters that are not relate to my simulation in MyLake model?

I want to Estimate surface heat fluxes using MyLake, but I don't have all the initial values in model parameters section and other sections,is there a way?

04 August 2024 1,537 1 View

Request a single Lecture notes for math as detailed as this that I can find in one place?

- The Existence/Uniqueness of Solutions to Higher Order Linear Differential Equations - Higher Order Homogenous Differential Equations - Wronskian Determinants of $n$ Functions - Wronskian...

03 August 2024 2,366 0 View

Tissue homogenization in mouse with FastPrep-24™ 5G - is the D matrix system useful?

I need to lyse and homogenise mouse tissues. So far I have experimented with liver and lung tissue, using matrix D. The liver was completely lysed with 6 repetitions of the standard program, but...

31 July 2024 9,186 0 View

Is it true that science is leaving the era of mathematics and entering the era of matrix mechanics?

We assume this to be true. Science leaves the era of mathematics and enters the era of matrix mechanics and the turning point is the discovery of numerical statistical theory called Cairo...

31 July 2024 3,900 2 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close