Standard curve shifting over time. How do I stabilise the ELISA?

24 February 2021 1,365 3 View

What are state-of-the-art methods/techniques/algorithms for the root-cause analysis of the anomalies?

I have been looking for research articles that target the question "why did an anomaly occur?", however, most of the papers that I found are related to "if an anomaly occurred?". I searched Google...

12 January 2021 7,951 3 View

Cross country comparison with matched pairs design?

Hi, I'm doing a cross-country comparison. My data for each country has a match pair design i.e. each company within a country is match with a control firm from that country. The data is...

07 January 2021 4,983 6 View

Stably transfected A549 cells are getting washed off during a plate based assay?

HI, I have transfected A549 cells with a plasmid of interest. The transfectants have been stably selected and clonally separated. I am doing a plate based fluorescence assay with the transfectants...

20 December 2020 1,222 4 View

What are the data analysis methods/techniques that can be used for matched pair data?

I have data in matched pair with one experimental group and one control group. I used conditional logistic regression for my analysis. Is there any other method which can be employed for data...

14 November 2020 9,034 2 View

Hello everyone,can we use content analysis method to measure environmental performance?

I am working on environmental and financial performance analysis of selected companies in India while reading several research papers i observed that environmental performance have been measured...

13 October 2020 527 11 View

Hello everyone, what are the sources of collecting secondary data regarding environmental performance and financial performance of co. in India?

While reading the annual reports of various companies I observed that some of the companies were following calendar year whereas others were following financial year.Since i have to do analysis of...

11 October 2020 2,584 7 View

No title

Hello Everyone, Any one having expertise in the associated field (MCDM - Manufacturing) mentioned in the flyer can contribute and recommend to others. Best Regards Dr. Pushpdant

05 October 2020 2,488 3 View

Is it appropriate to apply fixed effect model when the dependent variable is changing slowly over time for a given ID?

I am using a panel data set, where, my dependent variable is a score, moving slowly over time (24 years). Is it appropriate to apply a fixed effect model?. I have come across slides on "Panel...

27 July 2020 8,547 4 View

What are the good qualities of a teacher in current pandemic situation?

During the COVID-19 pandemic when all the teaching Institutions using online teaching methodologies. What are the qualities expected from the teacher?

12 July 2020 4,626 33 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

12% ledeburitic cold work tool steel, etched for revealing retained austenite, any help for clarifying?

Hello everyone. Given microstructure image belongs to a 12% ledeburitic cold work tool steel (annealed and tempered). The sample was etched with picral (100 mL ethanol and 4 g picric acid). I...

02 March 2021 4,119 3 View

Why Austenite grains in steel show much more twinning than ferrite grains?

It is oftentimes said to be a distinctive metallographic trait that differentiates a fully austenitic and a fully felly ferritic steel without etching that might distinguish between two. Why...

02 March 2021 728 2 View

What are the countries most affected by extreme rainfall as a result of climate change?

Increased heat, drought and insect outbreaks, all associated to climate change, have increased wildfires. Decreasing water supplies, declined agricultural yields, health impacts in cities owing to...

01 March 2021 7,168 9 View

How Can I bring as much common elements in steel as possible to calculate stable phase(s) in OpenCalphad?

As I was tweaking step-by-step OpenCalphad6 Macros step1.ocm involving phase and thermal property calculation of a High-speed steel, I could not incorporate more than 6 elements in the steel...

01 March 2021 8,840 1 View

I need to accelerate corrosion in steel parts that are used in a salt-water environment. Is there a technique for doing so?

I have a structure that employs d-ring swiveling tie-downs that corrode during use and become "frozen". I have sample swivel assemblies that I wish to corrode to see if I can free them using one...

01 March 2021 3,739 3 View

How to separate water from glycerol solvent in a solvent recovery vacuum distillation column?

I am currently doing my third year design project. I have been assigned to design a glycerol recovery column in vinyl acetate monomer production. The process unit before the recovery column is an...

01 March 2021 9,525 4 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Heat exchanger with liquid Nitrogen as coolant?

I want to cool Natural Gas from 195 Kelvin to 138 Klevin in a heat exchanger by using liquid nitrogen as the coolant medium. When entering the heat exchanger, the liquid nitrogen will have a...

01 March 2021 6,450 5 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View