Is it possible to do a baseline correction for a DSC test without having the empty pan line?

29 June 2020 0 7K Report

Hello all,

I have some old DSC data from long time ago. I need to do baseline correction for them but I don't have empty pan line for these data. I found out that for baseline correction, before each scan, a baseline needs to be recorded at the same heating rate and then subtracted from the experimental scan. But I don't have this data for my test. Is it still possible to perform baseline correction without having empty pan line?

Badges
Science topic

Similar topics
Correction

More Faezeh Iranmanesh's questions See All

How to incorporate a variable in damage model?

15 December 2020 7,284 2 View

Question regarding Primer Designing in qPCR?

Hi Everybody I have not done qPCR, and try to figure out the steps of that. From this regard, I am wondering Should primers designed for mRNA sequence or any other (cDNA, DNA, RNA) in qPCR, if...

07 December 2020 2,203 9 View

Mathematical or computational modelling of protein oxidation?

I am looking for a research paper about the mathematical or computational modelling of protein oxidation (caused by reactive oxygen species).. I would really appreciate that if someone helps me...

17 November 2020 2,340 3 View

Is it possible to still allow me to edit my article?

I made two errors in the references when modifying my article proof. Then I immediately informed the journal. But they prepared the article for publication. And published on the journal site.Is it...

16 November 2020 8,273 6 View

Can FEM model learn from experimental results?

I am looking for a research in which the finite element model was trained based on experimental results.

02 October 2020 9,277 19 View

Master thesis about the field of the luxury watch market?

18 September 2020 5,802 5 View

DLS: How to convert Number%,Intensity% and Volume% to q3,q6 or q0 distributions?

Hello, I am using a Malvern ZetaSizer for my work and as a result in this device, it is possible to get PSD based on Intensity%, Number%, and Volume%. My question is how to convert each of these...

14 September 2020 1,399 4 View

How can I access the Seqscape software 2.7 ?

Hi, I need Seqscape software 2.7 to analyze DNA sequences because this version supports 3500 sequencers. Please help me how can I access this version of the software? Thanks

17 August 2020 4,693 3 View

Is it possible for anybody to help me for fix bridge modeling in OPENSEES?

I modeled a two-span concrete box girder bridge base on FHWA design specification, and now I recognize a problem in modeling because my first period is higher than I expected. With initial...

12 July 2020 415 3 View

Why does stresses evolve in only one element in Abaqus explicit?

I am trying to run my VUMAT code with a model in Abaqus/explicit. After that the run has been completed, I observed that the stresses have been evolved in only one element as shown in the attached...

27 May 2020 5,506 3 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

No title

I am trying to find how to know the density needed for a pva electrospinning in a 0.6mm neddle, the electrospinning will be from top to bottom and the problem I really have is the solution because...

25 February 2021 2,615 3 View

How Can I clain a removal of a co-author?

I would like to make a correction in a co-author in your paper which is wrong. This name is also in other papers of Kenton Ko. Zey Ko is not a Co-author . The correct name is Zdenka...

24 February 2021 3,476 4 View

How does the injection volume impact LLOQ and ULOQ in regression analysis (LC-MSMS)?

Hello, I have run into an issue that has sparkled a debate at work: is the LLOQ/ULOQ impacted by injection volume under the following circumstances: 1) Same dilution factor of all samples 2)...

23 February 2021 9,159 3 View

How can I homogenize this data to make a meta-analysis?

Hi, I am doing a review and hopefully meta-analysis for my Master thesis but I have the following problems: - Some studies only give the difference between end trial and baseline data and other...

22 February 2021 1,115 4 View

Difficulty in debugging code to correct error - TypeError: '<' not supported ?

I am trying with a Unet code ontained from net ...in tensorflow. When trying to predict the segmentation result with the trained and saved model with metric " iou" using "CustomObjectScope"...

22 February 2021 5,254 1 View

HPLC baseline failure (ACN/Water)?

My baseline increases without any explanation, it is only fixed by changing the solution B, will it be the column? Reagents? Bomb? Detector? Solution A: H3PO4 0.01% IN WATER Solution B: H3PO4...

21 February 2021 5,656 3 View

How to perform Haldane correction on SPSS?

I was wondering if anyone knew how to perform the Haldane correction for SPSS (this is the definition of the correction -...

21 February 2021 2,882 1 View

absorption= 1-mag(S(FP1:1,FP1:1)S(FP1:1,FP1:1))-mag(S(FP2:1,FP1:1)S(FP2:1,FP1:1)) is it correct for absorption ?

hi everyone I am simulating a unit cell structure in HFSS using Flouquet port having two modes for absorption I have used this formula:- absorption=...

17 February 2021 9,178 2 View

How can I calculate the magnetic force applied from a magnet (no electrism)?

I would like to calculate the magnetic force on a Fe304 particle which is into a liquid solution . The magnet is above the solution , and there is no electricity. I found this formula : F = (V...

13 February 2021 4,770 3 View