Is it possible to calculate cpu time of calculation for free convection flow over plates?

More Kannan Thangavelu's questions See All

Python - TRNSYS link not working with Type169?

I used Type169 for data exchange between Python and TRNSYS. Unfortunately, facing the following error. No proper documentation is available for this part. TRNSYS Message 105: A TYPE was called in...

14 February 2021 5,577 1 View

Do we have any empirical model to model the combined effect of carbonation and chloride attack in concrete concerning climate change?

Do we have any empirical model to model the combined effect of carbonation and chloride attack in concrete concerning time-dependent temperature, relative humidity and concentration of carbon dioxide?

08 February 2021 4,277 1 View

Does AMBER or CHARMM force field parameters have coarsed grained side chain parameters?

I need to coarse grain the side chain with a single atom. However, what force field parameters do I have to use. Does AMBER or CHARMM have any parameters and partial charges for coarse-grained...

31 January 2021 7,091 3 View

Where can I read the force field parameters of amino acids and protein ?

I am a beginner in the field of molecular dynamics and biochemistry. I need the parameters such as van der Waal radii, partial charge of each amino acid. How do I read directly the parameters from...

20 January 2021 3,541 3 View

Can anyone clarify what is the difference between 'R' software statistics and SPSS Statistics?

I recently learned few things about 'R' programming language. It is open source / free platform in many aspects. R helps to descriptive statistics, inferential statistics, multivariate...

17 January 2021 1,089 20 View

Does anyone know what is the minimum variables required for standard deviation? and why large datasets is considered as reliable data?

For Descriptive statistics, we usually find out mean, median and mode as well as standard errors and standard deviation. Almost in research articles, I can see mean with standard deviation only....

10 January 2021 4,913 3 View

For mineral / compound characterization studies like FTIR, SEM, XRD, how many replicates should be taken for data analysis?

If we do some spectroscopy technique for only one sample, is it enough for data analysis or we have to do multiple samples from each treatment for getting authenticate results to publish in...

09 January 2021 5,896 2 View

What is the reference for the partial charges values for peptides shown in avagadro?

I built short peptides in Avagadro, using Build--->insert--->peptide. After constructing the short peptides of 4 amino acids(tetrapeptide). Under the drop-down, View--->Atomic...

27 December 2020 778 3 View

How to compute the Backward kinematics ?

I have been reading this paper. https://cnx.org/resources/9c9fe5128dfef772b498990a94c49df16c4f09ee/transformation_derivations.pdf Here, they have computed for forwarding kinematics to compute...

18 October 2020 8,208 3 View

How to plot the following XYZ coordinate file?

I am trying to plot the following points in VMD. It is plotting as points. However, It is not connecting the points from A to B to C to D to E to F to H by a line. How do I do it? If not in VMD,...

15 September 2020 4,282 3 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

Can we distinguish the type of free fluid inside the pelvic and abdominal cavities whether blood or serous fluid using the ultrasound?

during ultrasound examination of acute abdomen, sometimes we see free fluid , can we know the type of fluid ,whether blood or not , using ultrasound only? if yes , what are the sonographic...

01 March 2021 7,476 4 View