Antibody amino acid sequence database to simulation?

Hello, I need your help. I am looking for a database of antibody amino acid sequences for later simulation in a program in order to analyze their structure. The antibodies I need to test...

18 February 2021 371 4 View

How long can we consider that the data obtained with qualitative social research methods are "current"?

I cannot find any reference that deals with the temporal validity of qualitative data. I think there is a gap in the methodological literature on the temporal validity of the research results and,...

05 February 2021 9,788 20 View

Does DNA A-tailing survive after agarose gel electrophoresis and purification?

Hi everyone, I need to clone in pGEM-T vector the result of amplifying a metagenomic library by PCR with a high fidelity polymerase but I only want to clone the fragments of an specific size...

04 February 2021 6,051 8 View

How can I solve this problem with agarose gel DNA purification of bigger (1-4kb) fragments ?

Hi everyone, I perform a PCR + Restriction Digestion (single cut, same at both sides) over a metagenomic library. After that, I am trying to purifiy DNA fragments between 1-4kbp long from the...

24 January 2021 2,190 5 View

What is the most adequate (serum) dilution to use to determine IgE in mice serum via ELISA assay (commercial kit)?

We have a commercial kit from RayBioTech to determine IgE from mice serum. In accordance with the supplier's instructions, we have to use a dilution of 1:10000 of the serum. Is this dilution the...

06 January 2021 4,217 3 View

Is there any reference levels of IgE in healthy mice serum, like there are for other biochemical processes/components?

My question goes for reference levels of IgE in mice serum. I know that there are tables for the most common biochemical processes/compounds (red blood cells, white blood cells, AST, ALT, etc),...

06 January 2021 8,215 3 View

No title

It is important for me to know the opinion from your point of view as researchers.

30 December 2020 988 2 View

No title

13 December 2020 3,861 3 View

How can I do the bang's blinding index and james blinding index?

Hi! I would like to know with which statistical software the bang blinding index and the James blinding index and how to do it. Thanks

09 December 2020 1,363 2 View

Do anyone know a lab in Mexico where dielectric properties of solids and liquid can be measured?

I mean those kits that can be connected to vector network analyzers in order to find out permittivity and permeabilitty of solid and liquid from around 1 to 10 or 30 GHz

25 November 2020 852 1 View

Is it harmful to breed for Cre Homozygosity initially?

Hello, I am currently using a Cas9 knock in system that will be expressed in the liver. To do so STOP codon fl/fl Cas9 KI mice were bred with Albumin-Cre mice to generate heterozgous pups, that...

24 February 2021 5,759 3 View

How we can measure Kemp % in wool without using of benzene?

Would you please let me to know about the methods for measurement of medullation and Kemp % on animal? My problem is that the wool sampling and sending to laboratory is not possible. So I would...

21 February 2021 7,260 4 View

What is the difference between JCR impact factor and Science Citations index impact factor ?

If a journal Impact factor in SCI But no impact factor as per Journal citation reports . Is SCI valid

14 January 2021 325 5 View

Can you advise reference publications/standards on characterizing animal genetics research and development activities, and the outputs it generates?

I am doing semantic analysis of science and grey literature publications in the field of animal genetics and breeding. I have a standard dictionary but I am not sure if it captures the state of...

31 December 2020 4,924 3 View

Hello everyone, which software is preferable for simulating the effect of shrinkage of metal powders for the Additive manufacturing process?

Last time I was asked about simulation software to analyze the effect of shrinkages of plastic powder materials. Currently, an additive manufacturing process is what I find suitable for my...

29 December 2020 4,615 9 View

How do you characterise stainless steel 17-4 PH microstructure fabricated by selective laser melting?

Hello everyone, My project is to investigate the microstructure of stainless steel 17-4 PH fabricated by selective laser melting. SS 17-4 PH is predominantly a martensite matrix with some...

20 December 2020 4,037 4 View

Does the amount of ammonium measured by the electrode depend on temperature?

19 November 2020 6,315 12 View

LIFE in SMART CITIES: Animal data versus Human data, complementarity or not?

One observation is that in any city (those I know) you have humans, of course, but you also have many animals. Statistics of humans start with population data (for instance demographics) and...

08 November 2020 4,127 6 View

How can I decrease surface roughness in selective laser melting?

Recently, I study master degree in Taiwan. And my research topic is about metal 3-d printing with in718. I am required to decrease surface roughness in overhanging structure or inclined cube. Is...

02 November 2020 8,127 3 View

SAS code for a "Split-plot in time" (based on CRD design)?

Dear all, I want to analyze a factorial split-plot in time using SAS. Factorial Experiment using Completely Randomized Design (CRD); Factor A: treatments (a1-a4) Factor B: harvest time,...

28 October 2020 3,515 4 View