Is it necessary to decrease PDI to 1-2 in case the acrylic copolymer prepared and is supposed to be applied as skin adhesive?

22 April 2025 0 9K Report

co polymer prepared using Mini emulsion polymerization with surfactants as stabilizers, emulsion results in film formation along with stretchability and adhesion

Badges
Science topic

More Ayesha Sabir's questions See All

Could you recommend some articles on Urban Transportation System optimization and Innovation?

13 August 2024 2,595 3 View

Is there any cases algae not using the nutrient from the wastewater and grow normally?

I am working on microalgae cultivation using waste water. The initial concentration of nutrients were less but the microalgae has achieved biomass growth of 2 g/L. The final concentration of...

08 August 2024 4,812 2 View

1. If I can quantize the atom using this hyperbolic spiral and classical physics, could nature do the same?

If we map as a continuous motion an ionising electron (beginning its journey at n=1) in an H atom, a specific hyperbolic spiral appears (see animation). When we solve this spiral formula, we find...

07 August 2024 5,343 2 View

Articles on" Gender disparities i leatherwork education"?

Articles on" Gender disparities i leatherwork education"

07 August 2024 2,500 0 View

Why results of ROS flurescence are negative as there was no bacteria within?

Hello. I am working on ROS production of two systems: system A is cerium oxide and hydrogen peroxide, system B is cerium oxide nanoparticle, hydrogen peroxide and potassium bromide. I did some...

04 August 2024 5,974 3 View

What should I do with parameters that are not relate to my simulation in MyLake model?

I want to Estimate surface heat fluxes using MyLake, but I don't have all the initial values in model parameters section and other sections,is there a way?

04 August 2024 1,537 1 View

Why reactivity isn't increased with more empty spots in valence shell?

If from a geometric perspective the non-halogens, non-noble gases have more empty spots in their valence shell, and the filling/exiting of any of the empty spots in the shell constitutes a...

03 August 2024 4,787 2 View

Why is the molecule's orientation with an electric field affect polarizability?

Why is the molecule's orientation with an electric field affect polarizability? Electrons are diffuse enough to be independent with respect to orientation and effect of electric field on...

03 August 2024 7,843 1 View

Why don't d-orbitals split themselves, why does it take a ligand? why don't protons from ligand repel nucleus split d-orbitals?

why don't d-orbitals split themselves because of themselves without the presence of ligands? Electrons are indistinguishable. Why wouldn't it be more correct that protons from a ligand split the...

03 August 2024 3,589 3 View

Why doesn't chromium 2+ ion use all its d-orbitals to receive lone pairs from six waters in [Cr(H20)6)]3+?

I'm guessing it's because the ligand experiences too much electron repulsion or proton repulsion from the chromium to insert them close to the 3d-orbitals which are close to the metal nucleus. Is...

03 August 2024 1,370 1 View

What procedure should I follow for current controlled PPy film electrochemical deposition on ITO?

For example, I perform passivation process before electropolymerization of Py for adhesion to titanium surface. Is a similar or different procedure required for ITO? If necessary, I would be glad...

06 August 2024 3,176 0 View

How can I better use imageJ to get good result on calculating surface area of a film accurately?

I have images of film formed on the bottom of a 50mL beaker, and I have been trying to figure out the surface area. I could easily use features on imageJ to do that, but I want to know which area...

23 July 2024 4,461 1 View

How i figuer out the weight of curcumin powder?

I am trying to load curcumin emulsion in 4% chitosan gel but i don not know how many mg powder is needed ?

10 July 2024 2,462 1 View

Why can't I detect the plasmon resonance angle with water?

I am trying to measure the plasmon resonance angle of gold film and pure water using the Kretschmann configuration and a 633nm laser. Without flowing water over the gold, I can detect a clear...

10 July 2024 4,719 3 View

I want to ask why the poly aniline film does not stick to the ITO type substrate knowing that I used the electrodeposition method?

In order to make a polyaniline film, I used the electrodeposition method and set all the conditions, but I noticed that the polymerization process is happening, but it doesn't stick to the...

09 July 2024 2,708 2 View

What is the best way to get rid of unpleasant odour of acrylic emulsion beside redox post polymerization?

Even adding fragrance is not working

05 July 2024 741 2 View

Transparency oin-in-water emulsion but larger size particle ?

Dear Colleagues, I am currently formulating oil in glycerin/water nanoemulsionn of Thymol and Eugenol, using cationic surfactant. After phase diagram, I got trouble that the clear and...

03 July 2024 4,200 2 View

What is polymer/chemicals can increase the swelling index of a polymeric film?

Polymeric film such as latex rubber substrate or polymer

01 July 2024 8,343 4 View

How can we reduce the porosity of tungsten oxide (WO3) thin films during DC sputtering deposition (target: W, power: 100 W, 75 W, and 50 W)?

We are fabricating a tandem structure where a ~50 nm thick WO3 film is deposited between two metal films using DC sputtering. We use a mixture of Ar and O2 gases at different flow rates while...

01 July 2024 2,686 2 View

What are the potential effects of atomic-scale defects on the electronic and optical properties of thin films in emerging semiconductor materials?

Despite significant advancements in thin film deposition techniques, the precise role and control of atomic-scale defects in determining the properties of emerging semiconductor materials remain...

01 July 2024 5,745 1 View