How to cite SEER database?

Hi everyone I'm writing an article and I need data from SEER database. How should I add the reference?

13 December 2020 9,942 5 View

How can I find the area of contour with magnitude less than specific number?

Hello everyone I have results from fluent and I want to determine area with magnitude less than specific number for example for velocity or TKE. and also how can I determine Max and min diameter...

02 November 2020 5,863 3 View

Why does the classification_report for K_nearest Neighbors change by each run?

I am performing a KNN classification for a sample with n=5 and m= 200 (n:# features, m:#samples). To find the optimum value for K, I calculated an error rate for each K (1:50). However, I found...

28 October 2020 8,320 4 View

Why residuals stay at the same range in vof model in Fluent and it doesn't converge?

hi I'm modeling a 3d channel with vof , k-epsilon RNG with non-equilibrium wall functions , for bc I have velocity inlet, pressure outlet and for top of the domain I have used pressure outlet...

21 August 2020 5,926 7 View

Gas pump in Simulink MATLAB?

I need to put a gas pump that circulates a gas in a closed-loop system. However, I could not find a proper pump. Most of the available pumps are used for thermal liquids and are not suitable for...

24 April 2020 7,435 3 View

How to export CST antenna polar pattern to Matlab for further edits??

Hi everyone, I've got an antenna pattern in CST MWS that I want to transfer to Matlab for further edits in order to put it in the paper. But unfortunately, when I export from CST and import it to...

19 January 2020 8,481 8 View

How to analyse buckling of a model under coriolis force?

Hi everyone. Im trying to analyse buckling of a model under a coriolis force. My model is on my previous question. But i faced with this error in abaqus. DIFFERENTIAL STIFFNESS MATRIX IS...

29 October 2019 2,406 1 View

How to use strain gauge on springs ?

i am trying to apply strain gauge on springs i need some extra information 1. is it specific direction for adding rosette ? 2. is it any formula to choose size of rosette due to wire size ? 3....

26 August 2019 9,072 3 View

I set the time range to get data from every 10s in COMSOL but still it gives arbitrary data. Does anybody know how to solve this problem?

I study a time dependent process in COMSOL. I set the time interval to get data from every 10s. However in output I get arbitrary data.

21 March 2018 2,887 3 View

Does anybody know any software which can convert pictures from MHA format to .raw format?

10 July 2017 8,732 14 View

What are the pros and cons for mice versus rats?

Hi Everyone, I am designing a pilot study using rodents to assess the effects of simulated space environments (radiation + altered gravity) on microbiome and immune system. I have limited...

24 February 2021 1,825 3 View

Could the "incoming radiation (net radiation)" values be negative?

Could the "incoming solar radiation" values be negative? What is the difference between "global solar radiation" and "incoming solar radiation"? Which one might be measured negative values?

21 February 2021 7,726 9 View

Is the box plot of climatic indices better illustrate from daily data or annual data?

Hello, I hope you have a good time. I work on a research project about temperature indices. Due to the high number of indices, I only work on tables and maps on an annual time scale. In other...

19 February 2021 9,742 2 View

What is recommended and opened real-time or nearly real time geospatial data used in flood risk assessment and regional planning on a detailed scale?

I asked recommended real-time or nearly real-time data source for any parameters for flood risk on a microscale analysis for urban area cases in developing countries that had agglomeration urban...

18 February 2021 2,617 2 View

Can explain this diagram to me, is this the average consumption curve for one day or the total consumption of days in a month summed up in specific?

The hourly load curves of the selected household in each season are shown in Fig. 28. Figure 28 shows the demand for electricity in four months on an hourly basis. Can you explain this diagram to...

08 February 2021 657 16 View

Which model is most suitable for urban simulation?

Respected sir/mam, I want to simulate the urban expansion using different time series LULC based on satellite image. please suggest me most suitable model for urban simulation. Thanks and regards.

17 January 2021 9,134 11 View

How to open hyperspectral image in matlab which looks as clear as the same open in ENVI provided no change in the data formate?

I have download a hyperion data for Mt Fuji Japan. I have read all the extracted .tif formate data. When I produce the image in Matlab, it look foggy, but in ENVI it looks clear. How can I resolve...

17 January 2021 9,404 1 View

Was there any pesticide disasters other than Bhopal and Kasaragood tragedy around the globe?

Pesticides become prime compo in agricultural activities to meet the growing demand of the human population. But indiscriminate usage and mishandling led to two disasters in India such as Bhopal...

11 January 2021 3,790 7 View

Can anyone identify this fungus/mushroom from China?

The pictures were taken in Guishan Mts in Yunnan. The fungus is ca. 10-12 cm high.

07 January 2021 6,639 10 View

Is there any relevant technique for mesocosm studies in marine environment using Nanoparticles?

I am planning to perform mesocosm study in simulated marine environment using Phosphorus based nanoparticles, i would be using marine micro-organisms in it. kindly suggest me some effective...

07 January 2021 5,877 3 View