Is anyone working with WO3 precursor in CVD ?

More Nishtha Sagta's questions See All

Why Lactoferrin is not denatured at extreme pH and temperatures?

Hi, I want to study the temperature and pH stability of lactoferrin, so I performed Circular Dichroism (CD) of lactoferrin at different pH (pH 1.2 and pH 2.0) and temperatures but observed no...

26 February 2024 2,947 1 View

Hi, do you know how to differentiate between Lipid tubules and cochleates ?

I did FESEM of samples prepared from mixtures of phospholipids PA, PS, PC, PE and PI, but I don't understand whether these are cochleates or lipid tubules?

28 September 2023 1,658 1 View

Where can I find a standard procedure for reverse osmosis membrane autopsy?

I am going to perform a membrane autopsy of a reverse osmosis membrane to investigate fouling. I know how to do it based on research papers that i have read but I need a standard procedure...

24 May 2018 391 2 View

Can i use seawater of salinity 40 ppt to dilute 2 streams of brine of salinity 50 and 125 ppt each, to make a final discharge of 40 ppt?

According to the material balance carried out this required a volume of 1580 m3/h, but is this feasible? are my calculations correct? because I am using 40 ppt to dilute 125 ppt to 40 ppt again?...

17 March 2017 7,588 6 View

What are some operating reverse osmosis desalination plants and the silt density index of their intake sewater?

what are some operating reverse osmosis desalination plants in the and the corresponding silt density index of their intake sea water or the corresponding silt density index of any specific sea...

24 January 2017 8,843 2 View

Role of desalination in Millennium Development Goals?

Has desalination contributed to MDGs in any way? If so about what percent? How much safe water has been supplied to countries via desalination through MDGs? 2.6 billion people have gained access...

19 August 2016 2,728 2 View

Fouling and Scaling Mitigation in Desalination?

Where can I find free research papers on the above topic please? Tasks:1. Review of fouling and scaling mechanisms in desalination2. Mitigation assessment of the above3. Carry out a sustainability...

07 August 2016 489 6 View

What can be the maximum temperature loss of an uninsulated electrostatic precipitator?

By how much can the temperature decrease if the ESP is constructed of stainless steel and is uninsulated?

27 February 2016 5,848 3 View

Is there any valid justification for high Corona power ratio?

Corona power/flue gas volume lies in the range of 59-295 watts/1000 m3/h (neundorfer n.d). But when I calculated I got 905.13 watts/1000 m3/h while designing an electrostatic precipitator.

19 February 2016 1,939 0 View

How can I calculate percentage flooding of a distillation column?

FLV: 0.53 Ѱ= 0.1 how can i use the above figures to calculate percentage flooding from the graph attached below?

17 February 2016 9,603 3 View

Which Scopus Journal provides the most affordable fees?

"PUBLISHING IN A SCOPUS JOURNAL" Researchers are now at a cross road. The critical need to publish in a Scopus or ISI, etc journal is ever vital. Journal Publication fees must be submitted....

10 August 2024 8,621 1 View

Seeking Advice on Viability and Execution of Undergraduate Thesis Topic?

Hello everyone, I am currently developing a thesis proposal and would appreciate your input on its viability and how to effectively carry it out. My proposed topic is: "Does the perceived threat...

10 August 2024 8,992 0 View

Who will be moral responsible for the death of thousands of people in the event of an earthquake?

Who will bear moral responsibility for the deaths of thousands of people in the event of an earthquake? Weeks and months remain before the onset of strong earthquakes that bring death to...

08 August 2024 6,134 12 View

What procedure should I follow for current controlled PPy film electrochemical deposition on ITO?

For example, I perform passivation process before electropolymerization of Py for adhesion to titanium surface. Is a similar or different procedure required for ITO? If necessary, I would be glad...

06 August 2024 3,176 0 View

Are there any instruments for studying time similar to the way it is in space?

There are a huge number of methods for studying objects in space, according to the senses (and not only). Mechanical, thermal, optical, acoustic, electrical, magnetic, based on particle beams,...

06 August 2024 7,102 0 View

In the case of a wound l recurrence after radical breast cancer and sentinel lymph node biopsy. Are the sentinel lymph node procedure recommended?

In the case of a wound l recurrence after radical breast cancer and sentinel lymph node biopsy. Are the sentinel lymph node procedure recommended? If no axillary lymph node dissection was not...

05 August 2024 8,056 1 View

Regarding a model for simulating battery charge and discharge, what do you consider to be high fidelity?

Regarding a model for simulating battery charge and discharge, what do you consider to be high fidelity? What is the acceptable percentage of error (regardless of the metric)? Could you suggest...

03 August 2024 5,358 0 View

Interested in a SCOPUS collaboration?

Hi RG family. My team and I are working on some SCOPUS publications and we need co-authors who are willing and capable of undertaking both qualitative and quantitative-based studies. The scope...

02 August 2024 7,843 0 View

Interested in a SCOPUS collaboration?

Hi RG family. My team and I are working on some SCOPUS publications and we need co-authors who are willing and capable of undertaking both qualitative and quantitative-based studies. The scope of...

02 August 2024 8,572 0 View

Does continues partial charging/discharging do any harm to the BESS performance and degradation?

For a grid connected BESS (lets say 100 MW/200 MWh system, LFP battery), if we charge the BESS in such a way that whenever we can access power from the solar that will charge the BESS. Hence it...

01 August 2024 9,903 7 View

Maysoon Abdullah Ahmed

I would be glad if it was within my field of interest, but unfortunately it is different from my specialty

Jürgen Weippert

Building on this pretty old work, the surroundings of 1300 K would be a good starting point:

Article The Vaporization of Molybdenum and Tungsten Oxides

So, maybe start experimenting at 1100-1200K and ramp up until you see something.