22 August 2024 2 609 Report

mast cell stabilizers to prevent asthma

More Sreemoy Kanti Das's questions See All
For an in-vitro drug release study, what molecular weight cut-off (MWCO) dialysis bag is required for a 117 kDa protein?

kindly reply me. Thanking you in advance.

05 August 2024 7,727 4 View

How can we identify (in silico) the interacting amino acid residues or the nucleotides involved in the Protein-Protein / Protein-RNA interaction?

Hello! everyone, I am trying to study in silico Protein-Protein and Protein-RNA interactions. Now, is there any tool with which I can identify the interacting amino acid residues or the...

14 July 2024 950 2 View

Any suitable Animal models to evaluate Mast cell stabilizers?

I am looking for an in-vivo model to evaluate standardized herbal extract for its potential as a mast cell stabilizer.

14 July 2024 779 0 View

What is the mathematical expressionof theoretical yield strength calculated considering solution strengthening in stainless steel 316L?

In the expression for solid solution strengthening model that has been widely used in the literature use a linear form consisting of strength coefficient, and concentration of elements in wt.%....

11 July 2024 4,476 3 View

How to insert cholesterol inside DPPC membrane by replacing same number of DPPC molecules in GROMACS?

I am trying to insert cholesterol inside the DPPC membrane by using gmx insert_molecules -replace. But number of DPPC molecules replaced is much higher than the number of cholesterol inserted?...

30 June 2024 4,160 2 View

How to synthesize Dichloro(p-cymene)ruthenium(II) dimer in a good yield?

Suggest some procedure where i can synthesize [Ru(p-cymene)Cl2]2 in a good yield.

23 June 2024 9,244 2 View

Analysis of microbial biomass for nutrient cycling?

It will be an honor, if anyone can suggest the standard methodology for analyzing nutrients(N,P,K) in soil microbial biomass

23 June 2024 3,850 4 View

Can i use polystyrene as a matrix in a hybrid COMPOSITE?

fiber powders will be used as a reinforcement.

23 June 2024 10,027 3 View

After expert validation of the research tool for data collection, what should be done first after piloting. Reliability analysis or factor analysis?

Which would be prefered first (factor analysis or reliability analysis of a Likert type scale)

19 June 2024 9,378 4 View

Which media will produce more biomass in saccharomyces cerevisiae?

Dear all, For higher biomass for saccharomyces cerevisiae which media is suitable in shake flask? 1. YPD media 2. Basal salt media and what is the optimum C/N ratio ( 5:1 /10:1). Thanks &...

18 June 2024 2,106 0 View

Similar questions and discussions
How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Is there any way to quantify bacterial and fungal cells in their mixed culture?

I am working in fungal fermentation of soybean meal and there is bacterial growth in them at times. I am trying to quantify fungal cell counts and bacterial cells; but I haven't been able to do at...

07 August 2024 7,535 4 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Why activated CAR-Jurkat cell could not kill targets?

Previously when I co-coluture anti-CD19(FMC63) CAR-Jurkat with Raji with E:T=5:1, Jurkat can eliminate Raji in 24h. However, when I test another CAR construct, although I can dectect totally CD69...

06 August 2024 641 2 View

How much total RNA concentration to be extracted from sorted plasma cells from bone marrow of C57BL/6 mice for RT-PCR ?

i have sorted anti-NP specific plasma cells from bone marrow of C57BL/6 mice at certain times after immunization with variable counts and isolated total RNA using TRIZOL method for RT-PCR using...

05 August 2024 8,835 1 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close