Unable to match simulation results with literature?
In External Quality Assessment (EQA), lab result is acceptable with peer group, but unacceptable with method group. So what can be done ?
01 September 2023 5,284 1 View
Are there any established laboratories or research institutions known for their expertise in performing carbonic anhydrase enzyme inhibition assays? I am particularly interested in identifying...
11 June 2023 8,118 0 View
I am currently working on a project using abaqus direct cyclic and facing few issues. The stabilized cycle response which is expected after few no of cycles is being shown as output at step time =...
10 August 2021 8,401 3 View
Hello everyone I am trying to simulate a cantilever beam with direct cyclic analysis approach. The pattern of the loading is given in the picture. However, at step time zero, the values of stress...
30 June 2021 3,764 0 View
For the case of crack propagation abaqus provides both the above methods. What is the difference between the two? The usual answers seen are just mentioning that one uses CZM and another LEFM. If...
20 June 2021 4,816 2 View
Hello everyone Recently I have been trying to import mesh created in hypermesh software and trying to import into abaqus. However, I am not able to continue, since parameters such as sections...
11 April 2021 2,225 7 View
Hello I am working on a project involving ABAQUS XFEM for stationary crack to obtain SIF and for crack propagation. However, I have encountered few problems. I have listed them below. 1....
07 April 2021 8,389 1 View
The motivation behind the question is that only young's modulus is available in tension for most of the materials, and compressive modulus is assumed equal to tensile modulus. There is a need to...
09 February 2021 7,715 3 View
This is required since the stress v/s crack length has to be determined
23 December 2020 3,689 1 View
My name appears in various articles asas Vishwas Sovani Sovani VB Sovani Vb V B Sovani In case of the above article it is the third Sovani Vb
04 October 2020 728 1 View
I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...
08 August 2024 4,831 4 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
Details of the Analysis. Static Analysis Composite Layup Continuum Shell Elements FRP Material (Elastic and Hashin Damage)
03 August 2024 8,538 4 View
Hello, colleagues. Recently, I have been working on a metal processing simulation with my UMAT in Abaqus. I have outlined the corresponding simulation, but I keep encountering issues that cause...
30 July 2024 7,062 1 View
I am trying to run a restart analysis, which imports deformed configurations of parts from a generated ODB file. It runs fine in Windows OS but when I try to run it in Linux OS, it is giving some...
29 July 2024 9,572 3 View
Sure, here is the translation: I have a 3D orthogonal woven composite structure where warp, weft, and binder yarns are oriented in three directions. After modeling these yarns and the matrix in...
28 July 2024 8,169 0 View
I know that films and other low-thickness laminated products are produced using biaxial orientation, but is there something similar for sheets with a thickness of around 6 mm? Or are they...
21 July 2024 1,559 1 View
hi, I am doing a risk analysis of a cylindrical fuselage with windows. I have applied contact interactions between the different parts, and I have applied a unit value load to a reference point,...
20 July 2024 647 2 View
Hi all, I am using the element deletion process based on a Tsai-Wu criterion through a UMAT with a specific State Value controlling the process (DepVar -> Variable number controlling element...
17 July 2024 1,501 1 View