How can I measure MMP-1 protein activity or protein level from liver tissue?

Instead of checking only the mRNA level, I want to check the active protein level of MMP-1 in Liver tissue from mice. How can I do that?

03 March 2021 1,763 2 View

Binary Logistic Generalized Linear Mixed model in SPSS. Is it doable?

I want to analyses the proportion of swimming sperm of three species of fish in two salinities. To analyse the proportion of swimming sperm in a Generalized Linear Model, I would use a Binary...

03 March 2021 2,297 3 View

Looking for Materials with high thermal expansion coefficient and high temperature resistance?

03 March 2021 8,272 1 View

Guidelines for survey (question type) analysis?

Hi. Please tell me what guidelines should i need to follow for questionaries' type research work in India. It is not hospital based work, we are conduction basic institutional based qualitative...

03 March 2021 2,037 3 View

What are the values needed for gabor filter's parameter for cifar10 data?

Hi, I implemented a code to gabor filter cifar10 data but the images after being filtered and stacked are not clear like the original images. I think the problem is in the way I am using the...

03 March 2021 6,317 1 View

Can we block unwanted images during the x-ray prediction?

i am try to classify the x-ray images. During classification , can i block unwanted images (except x-ray image).

03 March 2021 7,100 1 View

No title

03 March 2021 5,360 2 View

What techniques can I use to determine the miscibility of polymer blends?

The term miscibility refers to the single-phase state in thermodynamics. I do not mean the compatibility of different components. To determine the miscibility I know several techniques such as...

03 March 2021 4,107 4 View

Sample dilution for quantitative analysis using ELISA?

If the detection range is in ng/ml but the reference range is in ug/ml for a molecule or protein in serum or plasma .how to dilute and what is the initial volume to be taken for quantitative analysis

02 March 2021 7,670 3 View

The procedure compute?

02 March 2021 5,204 3 View

Why does intensity drops as concentration increases?

Is there any reason for decrease in fluorescence emission intensity of HSA,BSA when increase the concentration ?

28 February 2021 3,653 4 View

What is the proper range of FRET efficacy?

I would like to use FRET effect to probe the distance between two functional moieties (I am sure the distance is smaller than 10 nm). I have tried several times, but I found out that the FRET...

21 February 2021 3,562 1 View

Interpretation of a fluorescence Emission spectrum ?

Hello, i work with a spectrometer which only render the fluorescence emission spectrum. Until now i just found how to interpret an exitation- and emission spectrum together to generate deeper...

20 February 2021 1,291 3 View

ZnS oxidizes to ZnO!!why??

when I put my ZnS solution in the chemical bath, the ZnS oxidizes so there are ZnO peaks appearing because of the reaction with the oxygen in the air, despite the fact that I close the beaker...

14 February 2021 5,778 9 View

Receiving very less number of hits and events in acoustic emission tests?

I am doing a three point bend test with concrete specimen of dimension 280mm*90mm*90mm. I am putting 2 sensors near the notch with 3cms away from both the sides. the experiment ran for 20 mins but...

13 February 2021 2,990 1 View

How to modify micro-structure of Pure Copper which is available as a flat plate of 25 X 25 sq. cm?

Hi everyone, for a thesis project I have to modify the micro-structural properties of pure Cu flat plate of dimension 25 X 25 sq. cm . As I tried searching the available literature, I found a lot...

09 February 2021 5,090 3 View

Xrd result of ZnO thin film shown better crystallinity at low temperature and the crystallinity decreases as the temperature increased. why?

I have synthesized ZnO thin films at four different substrate temperature say, 300, 350, 400 and 450C. and the samples were annealed at 450C for half an hour. the xrd result shown better...

04 February 2021 7,641 4 View

How can I multiply values with standard distribution and with triangular distribution?

I am calculating emissions considering the uncertainty of the data to do Monte Carlo simulation. Some variables such as yields have normal, lognormal or even uniform distributions. These must be...

03 February 2021 6,318 5 View

How do I analyse a Photoluminescence Spectrum ?

I have a few questions related to PL (images attached for same material by 2 methods), It would be great to get some help. 1. What is the physical meaning of highly intense PL? Does this mean...

02 February 2021 1,791 3 View

Which method is preferable for cutting the nanocomposites?

Which of the methods like water jet cutting, diamond cutting, laser cutting, etc. is more suitable to cut the carbon nanotubes reinforced epoxy composites into test sample to ensure the clean...

29 January 2021 1,354 5 View